morganew Posted October 29, 2012 Report Posted October 29, 2012 A friend and I are about to "go halvesies" on a Powermatic 701 Hollow Chisel Mortiser (it will live in my shop, so I'm getting the better half). All that is left to decide what to do about chisels. I currently have a set of cheap chisels that came with a drill press mortiser kit - delta brand. If I'm getting a 701 PM, I might as well get some chisels to go with. It looks like my choices are: 1. Inexpensive CMT chisels that run about 18-20 each 2. Powermatic set of 4 for 169.00 3. Lee Valley set of 4 for 172.00 Opinions? experiences? Quote
Boatworks Today Posted October 29, 2012 Report Posted October 29, 2012 I have the PM chisels and really like them with one small exception. When I first got them I had to take a fine metal file and hold it against the edge of the square cutter and let it spin for a few seconds as the auger bit had a tendency to wallow a small bit outside the chisel area. Here are a few pics of what I mean. After cleaning up the edge with the file it was perfect. BTW I usually order my PM stuff from a CPO outlet as they have the best prices. Here's the same set for $159 http://www.cpopowermatic.com/powermatic-1791096-4-piece-mortise-chisel-and-bit-set/pwmn1791096,default,pd.html&carousel=3 I'm using the chisels on a PM719T Quote
morganew Posted October 29, 2012 Author Report Posted October 29, 2012 I read about this "wallowing" on another post, though I don't quite think I understand what you say you are doing here to correct it. are you saying to take the file and lay it flat against the side of the cutter and essentially file down the outside diameter of the auger bit? It seems crazy that this is a known problem with the PW chisels, and yet they still want to charge 160 plus for them. Then again, I don't know if other chisels do worse things, making the need to reduce the diameter of the auger a minor point. Quote
Boatworks Today Posted October 29, 2012 Report Posted October 29, 2012 are you saying to take the file and lay it flat against the side of the cutter and essentially file down the outside diameter of the auger bit? Yes. by laying the file flat against the cutter it shaves off any part of the auger the extends beyond. I turned the mortiser on and gradually brought the file into the cutter until it was flat; then left it there until I didn't hear anymore contact between the auger and file. Took about 2 min per chisel.. Other than that, very happy with them. Extremely sharp and holds an edge. I haven't honed or sharpened any of them and they still work great. My most used chisel probably has 200+ mortises on it going through teak and mahogany. Still cuts like a champ Quote
CessnaPilotBarry Posted October 29, 2012 Report Posted October 29, 2012 I also have the PM chisels, in a PM719. I touched them up with an 8000 grit stone on the outside and diammond cone inside, and have been happy with them. I don't have the wallowing problem. Quote
morganew Posted October 30, 2012 Author Report Posted October 30, 2012 Anyone use the Lee Valley models? Quote
Rick LoDico Posted October 31, 2012 Report Posted October 31, 2012 The Austrian-made Delta chisels are excellent for about the same price as the PM. Quote
CessnaPilotBarry Posted October 31, 2012 Report Posted October 31, 2012 You might want to give the Delta's a coning and polish before you spend money on new chisels... Ya' never know... Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.