Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Rewiring table saw from 220 to 110

Featured Replies

As far as your electrical panel goes... The best assumption to make is that if there is a breaker in the slot there is most likely a circuit attached. you do however have several spaces available in the panel...looks like room for 1- 220v double pole and 2- 110v single pole breakers.

It doesn't seem to me that you are very comfortable with electricity... So I have to go with the others and say either hire an electrician or find a friend who will help you.

If you did want to tackle the project of adding a circuit (which would be the best and most right way of handling this problem). You would have to start by shutting off the main breaker to the panel. Remove the front cover from the panel. It is very important to know that the main lug wires going into the main breaker will still be hot! DO NOT TOUCH THOSE WIRES!!! get a 20amp 220v double pole breaker that is made for your panel it will go in the lower right side of the panel. Run conduit to an electrical box from the main panel. Run 12ga wire from the panel to the box. You will need to run 3 wires a ground and 2 hot leads. You can go to your local HD and purchase a receptacle and plug that match both rated for 20amps 220v. I use twist locks with the following part numbers L620P for the plug and L620R for the receptacle. Wire the two hot wires into the hot leads on the receptacle and the ground to the green lug.

At this point I would also recommend replacing the cord on the machine with 12-3 power cord that you can buy by the foot from HD. Wire the plug to one end and the other to the machine.

Now with the receptacle secured and attached to the box with the appropriate cover, wire the breaker. Attach the two hot leads to the 220v double pole 20amp breaker the ground goes to the bonding strips connected to the box.

Slide the breaker into it's slot and leave it in the off position. Turn on the main breaker which will re energize the circuits in the panel. At this point you can switch on the new circuit and test the receptacle with a simple voltage tester making sure that everything is working properly.

If you wanted to just hook the machine to the drier outlet you would need to buy the 10-3 power cord from HD by the foot and find the appropriate plug end that matches your drier receptacle. Wire the plug to one end and the other to the machine.

The above mentioned RV extension cord is made for a 110v circuit not a 220v circuit. My concern is that the plugs would be different but i am not sure about that. I do however think that it would be cheaper to just buy the cord by the foot and the appropriate plug that works with the dryer.

Hopes this helps...

I just spent a min to look at the specs of your saw. The 2 hp motor will only draw 8amps at 220v. It also says that it comes with a supplied NEMA 6-20 plug. You can purchase the appropriate receptacle at your local home center and wire that in.

And as for the topic of this post re wiring it to 110 would not be a great idea for several reasons.

First there would be a large amp draw that would create a lot of heat even in a 20A circuit. Second The motor will run more efficiently at 220v than 110v. And even though a 2hp motor has the option of being 110v I would say the largest 110v motor should be around 1.5hp. I have converted every tool in my shop to 220v. My 1.5hp jointer sounds and runs better at 220 and starts faster at 220v.

Something to think about....

  • Author

I just spent a min to look at the specs of your saw. The 2 hp motor will only draw 8amps at 220v. It also says that it comes with a supplied NEMA 6-20 plug. You can purchase the appropriate receptacle at your local home center and wire that in.

And as for the topic of this post re wiring it to 110 would not be a great idea for several reasons.

First there would be a large amp draw that would create a lot of heat even in a 20A circuit. Second The motor will run more efficiently at 220v than 110v. And even though a 2hp motor has the option of being 110v I would say the largest 110v motor should be around 1.5hp. I have converted every tool in my shop to 220v. My 1.5hp jointer sounds and runs better at 220 and starts faster at 220v.

Something to think about....

I am dead set on running at 220v, that is for sure. Just the method on how I wish to accomplish it is in question.

From all the amazing posts and replies in this thread, I am really down to two options:

1) Wire in a 220v breaker and new line to the shop.

2) Run an extension cord and plug it into my dryer outlet.

I would really like to go with the first option, but I would like to know that the second option is just as viable if used.

I'm really going out on a tangent here, and believe me I would not do this on my own without consultation of a professional. But, what if I had a junction made from the dryer outlet? Hypothetically, this would bypass having to purchase a new breaker and such. Just an idea, and if it is a bad idea let me know why.

EDIT:

Also, if I was going to have a new line run, should I use solid tube conduit or would the flexible stuff work? I would have to maneuver quite a bit to have it get where I want it in my shop.

The 30amp rv cords are more than adequate to run your saw They are made to run all systems in a rv and they are 220. I have two of them and

they run my stove,refrig, and two roof ac in my 30 ft fifth wheel rv. Its a bad idea to run a separate box from the dryer outlet just in case the dryer was to turn on while the saw was running I know its a pain to unplug and replug when using the same outlet but since its only short term its the most basic direct way.

Just to add another option to a dizzying array, you could also run it off your electric water heater drop if that is near by. I ran a couple 220V tools off mine for a long time. My water heater is on a timer that ran in the really wee hours of the morning so it was never a problem plus the timer on the heater had an override if I wanted to cut something at 4am (don't laugh, I was in there until 5:30 am yesterday :-/

For the dryer, your electrician friend could easily make a switch box for you; plug it into the outlet, plug the dryer into the box, run an extension to your shop. Have a switch on it to set which of the two gets the power. Sure there's the argument that someone will flip off the table saw while you can clearly hear it to run laundry, but no fool-proof setup is immune to the clever fool.

Advantage of stealing off the dryer outlet is the availability of a neutral so you could break out 220V and 110V at the other end. Nice.

  • Author

Just to add another option to a dizzying array, you could also run it off your electric water heater drop if that is near by. I ran a couple 220V tools off mine for a long time. My water heater is on a timer that ran in the really wee hours of the morning so it was never a problem plus the timer on the heater had an override if I wanted to cut something at 4am (don't laugh, I was in there until 5:30 am yesterday :-/

For the dryer, your electrician friend could easily make a switch box for you; plug it into the outlet, plug the dryer into the box, run an extension to your shop. Have a switch on it to set which of the two gets the power. Sure there's the argument that someone will flip off the table saw while you can clearly hear it to run laundry, but no fool-proof setup is immune to the clever fool.

Advantage of stealing off the dryer outlet is the availability of a neutral so you could break out 220V and 110V at the other end. Nice.

That switch idea is a fantastic idea. I will absolutely look into that if I can not have a permanent line run.

Basically, I wouldn't mind an extension cord that I would plug in every time I wanted to work, but I'm not to sure my dad would be keen on that :)

Oh the woes of living with your parents *sarcasm*

I'll find a solution, that works with all of us.

Better keep mom happy if you forget to replug her dryer or throw that switch shes gonna voice her opinion and that will be the only one that matters

  • Author

Better keep mom happy if you forget to replug her dryer or throw that switch shes gonna voice her opinion and that will be the only one that matters

Exactly :) Have to make it seamless as though nothing new was ever put in.

Have your electrician friend do the wiring. It isn't difficult, but that looks to be a subpanel and the wiring is different there than a main service panel. Hard to be certain since the important part (the top) was cropped off.

With your sub panel mounted on the outside of the wall wiring in a new receptacle with some conduit will be the best way to hookup your new circuit.

  • Author

Have your electrician friend do the wiring. It isn't difficult, but that looks to be a subpanel and the wiring is different there than a main service panel. Hard to be certain since the important part (the top) was cropped off.

I'm not really sure if it is a sub-panel or not. Although, I'm pretty sure there is no other panel for my house. I am going to talk to my dad tonight when he gets home and see if he is on board for the new addition. If not, I'm pretty much sunk in the water, but if so it's game on.

I also have a question of receptacle placement in the shop. I have a column in my shop that is attached to the structural I-Beam that spans my house. It is a metal pole, so I can't just run wire through it. I was thinking maybe having some conduit run down from the ceiling and have a receptacle box attached to the pole with a hose clamp or something. Is this viable, or would I risk something?

I call it a sub panel or secondary panel. Im sure your house is bigger than the panel in the photo could support. Running your wires on the outside of the wall, ceiling and pole is what the conduit is designed for so no problem with the pole mounted access.

  • Author

I call it a sub panel or secondary panel. Im sure your house is bigger than the panel in the photo could support. Running your wires on the outside of the wall, ceiling and pole is what the conduit is designed for so no problem with the pole mounted access.

Where would the main panel be then? My house isn't too large, and probably illegally wired since the circuits are rather large. By that I mean, most of the 2nd floor and all the basement are on one breaker. I would have that changed, but since its not my house I have no say so.

Just like when I asked about having the new line installed, I was told "you don't need a new saw, etc, etc" so it's back to square one.

Again, the woes of living with your parents. Ha.

I just assumed since it sounds like this is a basement area and you had more than 1 floor your panel was larger than the one in the photo

Im sure your dad will know if there is another panel. I think we got side tracked on the sub panel mystery though if hes ok with you taking the last spot in the panel for the saw you should have no problems getting 220 to your new TS.

  • Author

I just assumed since it sounds like this is a basement area and you had more than 1 floor your panel was larger than the one in the photo

If no one is home you could always just throw the main breaker at the top if all the lights and power go off in the house this is your only service panel.

or just wait and ask your dad if there is another panel. I think we got side tracked on the sub panel mystery though if hes ok with you taking the last spot in the panel for the saw you should have no problems getting 220 to your new TS.

Well it's no big deal, I do enjoy learning things like this.

As of now, no table saw for this house. I have two choices. I can either work on convincing him from his dogmatic perspective, and continue to use the tools here. Or, I can start my own collection of tools and set up shop at my finances parent's basement. Free space, but need to buy my own tools :)

What's a guy to do! :) gotta stay positive though.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.