Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Dust control.....

Featured Replies

I am just starting to plan my shop build this summer and was curious as to what dust collector to buy. All my tools will be stationary. Are cyclones the way to go or just go with a 2 or 3hp canister style? I would likely be running 4inch piping to each piece of equipment. Also, I would like to have my tablesaw and outfeed table in the middle of the shop and am curious if people put power outlets within the slab so to not have to trip on cords all the time? 

Thanks

Shane

How big is the shop, and about how many tools are going to be going at any given time?  Is it just you in the shop or do you have employees or friends/family that work at the same time?  This will help to determine how much CFM you will need.  For a sole hobbyist, a 2-3 hp should be fine.  (I think they run ~1000-1500 cfm). 

 

There are a lot of ways to acheive the results of a "Cyclone", so I would reccomend doing some DIY research and see if it's something you can do yourself.  Prefab cyclones like "Clearview Cyclones" are awesome, but can run up the budget.  If you are needing to skinny the budget a bit, this is one of the areas I think you can save a bit. 

 

Power in the slab is definatley a nice feature.  So if you haven't poured yet, I would reccomend putting them in.  It's relatively inexpensive if you plan for it.  It's very expensive to add it after the fact. 

 

If you have support beams running through the middle, you can also, frame those in, and run electrical through them to give you close enough plug ins. 

It sounds like you're talking about a dedicated, single location dust collector.  Which means you've already ruled out moving a collector from tool to tool as you use it.  Nothing wrong with that, but it means you are looking into what I call the "big boys."

 

If you haven't checked out Bill Pentz's site, you might go ahead and do so, but if you aren't already an engineer, you might get overwhelmed in seconds.  (My experience has been that engineers get overwhelmed in minutes.)  It is a great resource, but it should be mentioned it is not the only resource.  This may also be what Chris H is referring to when he says to "skinny up the budget," as there are concepts and plans there to build your own cyclone.

 

You have the option of a single stage or multiple stages, cyclones, trash can lid adaptors, and more.

 

Or, you can go the "shop vac" route, and add a second stage to the shop vac.

 

The 1500 CFM category will work for your bigger chunks, or your longer runs.

 

My suggestion would be to test out your tools now, before building the shop, to determine which tools work with what style of dust collection.  Now, don't panic about the cost; I'd start cheap using what you already have.  Marc has a video on dust collection, and has addressed this topic repeatedly, and there is continual debate about 4 inch versus 5 inch.  I'd also chat with Vic, who has a phenominal thread on building a shop (someone needs to post the link, as my time is ending shortly).  This will address both power and ducting.  You might find you don't need nearly as big a CFM as you might think.

 

Marc also has addressed the power in the floor topic, and I think most people would agree that this is a very good way to go.  Even if the tools will not remain in the current arrangement.  I certainly would not hesitate to consider 220 in the floor, as long as local code allows.  For coolness factor, though, I'd lean towards the RoboReel video in the ceiling.

 

(I need to state that currently, aside from my lathe, my dust collection is pretty much covered by a broom and pan.  Yes, the drill press is not convenient to clean up, but it's not impossible.  And I get away with a small vacuum hose to clean out the corners.... semi-annually.  So I haven't gone "big bore" on the dust collection.  merely the explanation.)

I'm kinda thinking that this is something that is "understood" but hasn't been mentioned yet in this thread is the in-expensive option of a good respirator until you get the details sorted out for a shop system... 

 

Technically this is all you would need (health wise) but unfortunately there isn't a model / brand of mask avail that knows how to work a broom or dust pan :P !!! 

 

Still gotta clean....

  • Author

hey thanks for the replies. the shop will be 26x32 equipt with bandsaw, lathe, drill press, cabinet saw etc.... I will be working alone so one tool in use at a time. I am building a seperate room to house the compressor and dust collector. I am sure the distance to the farthest tool could be 25 feet. All the tools will be against a wall with the exception of the tablesaw. Is the best way to run the pipe for the tablsaw to drop it down from above?

Thanks

Shane

Personally, I'm more of a fan of drop cords than of in floor outlets.  Might be because I'm in an area where floors can get wet - seepage, condensation, spring flooding ...   Ok, I don't get spring flooding so much as snow melt that can run any where.

 

Anyway, water tends to flow down rather than up so I see drop cords as MUCH safer.

Go with the cyclone...bigger the better...sounds like you can afford it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.