Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Garage finishing question

Featured Replies

I am going to convert my two-car garage to a workshop. It is currently attached to the house on one side which is a bare cement wall. The other three sides are uninsulated 2x4's on 14" inch centres. It has a peaked roof of what look like 2x6 rafters. They are also uninsulated. The ceiling of the garage is open joists. Most of them have plywood or other boards on top forming a small attic in the garage.

I want to insulate and finish the shop but only as much as I practically require as I'm going to be selling the house in about 3 years. I plan on adding some sort of heating system in the fall. However before I start adding tools I want to take advantage of the open space to get the insulation and finishing done now. I plan on insulating the garage and dry-walling it.

So first - the concrete wall common between the garage and house. Apart from aesthetics, is it necessary to stud, insulate and put drywall on this wall?

Second, if I insulate the roof rafters of the garage (the ceiling of the attic portion), do I need to drywall the ceiling of the garage? The ceiling joists look very uneven and I think that dry-walling it would be a big challenge. Aesthetically it isn't anything that bothers me.

Any advice would be greatly appreciated.

If you haven't already gone through I'd check here for questions and answers.  Then, I'd send Vic a twelve pack of his favorite "grape soda" beverage, and spend a weekend talking shop (literally) with him.

 

One thing I would consider, but I am not anywhere knowledgable about it, would be to add a thin foam board to the concrete wall, with narrow furring strips powder nailed into the wall, and cover everything with plywood paneling... but again, I'm not the expert.  (I muddle the waters.)

snapback.png

Whatcha gonna do with them Vic ?

 

 

They'll probably go toward a design I'm working on for a dining table.

 

 

I am going to convert my two-car garage to a workshop. It is currently attached to the house on one side which is a bare cement wall. The other three sides are uninsulated 2x4's on 14" inch centres. It has a peaked roof of what look like 2x6 rafters. They are also uninsulated. The ceiling of the garage is open joists. Most of them have plywood or other boards on top forming a small attic in the garage.

I want to insulate and finish the shop but only as much as I practically require as I'm going to be selling the house in about 3 years. I plan on adding some sort of heating system in the fall. However before I start adding tools I want to take advantage of the open space to get the insulation and finishing done now. I plan on insulating the garage and dry-walling it.

So first - the concrete wall common between the garage and house. Apart from aesthetics, is it necessary to stud, insulate and put drywall on this wall?

Second, if I insulate the roof rafters of the garage (the ceiling of the attic portion), do I need to drywall the ceiling of the garage? The ceiling joists look very uneven and I think that dry-walling it would be a big challenge. Aesthetically it isn't anything that bothers me.

Any advice would be greatly appreciated.

The only reason you would need to insulate the common wall (concrete) is for sound proofing.  It's not necessary, as that is a common wall to the heated envelope of the house.  If you plan to insulate the roof deck, no you do not need to also sheet the ceiling.  You will need to sheet the roof deck after the insulation.  Opinions differ to whether you need to provide ventilation on a full bay insulation in direct contact with the roof deck.  I would check your local code for direction on their opinion.  If so, you'll need to get a continuous air gap from a vented bird block to a ridge vent.  If not, then it's not going to be nearly a big of a job.  Also, air seal everything.  A coat doesn't do much good if its not zipped up.

 

Also, double check, but your stud placement should be 16 inch on center, not 14.  

 

Feel free to DM me if you have any questions. 

The easiest cure for uneven ceiling joists is to run 1 x 2 strips 90 degrees to the joists and screw them tight to the lowest sections and shim the gaps. You can buy bundles of shims pretty cheap. I shoot them in place with a nail gun then screw through the center. A string stretched tight will give you a straight enough line for a shop ceiling. 1/4 plywood might be easier to hang than Sheetrock , but paint it white to get all the light needed for your shop. Vic knows plenty about light and everything else on setting up a shop!

Check and see if the concrete common wall is insulated from inside the house if so then why bother, unless it is more for reducing shop noise in the house.

I would think a finished insulated garage would be a positive thing towards selling the house. Potential shop, hobby room or Man cave for a buyer!

Steve is correct that furring down the ceiling joists is and sheeting the ceiling rather than the roof deck is preferable.  I would still recommend using sheet rock and taping the seams over using plywood because the ceiling plane has a lot of pressure from stack effect and should be air sealed to mitigate heat loss.

I'm assuming you're planning on fiberglass batt insulation, as that is the easiest DIY approach to insulating the walls.  Be sure to read up on how to install correctly, as the performance of fiberglass batts diminish excessively if not installed properly.  Here is a link to get you started.  http://www.greenbuildingadvisor.com/blogs/dept/musings/installing-fiberglass-right  This article links to another at Energy Vanguard that shows typical mistakes made during installation.  The beauty is you're not being paid by the job, so you can take your time and miss the pitfalls of an improper installation.

  • 3 weeks later...

Ottacat,  i know you primarily seemed interested in insulating the space, and i noticed you asked about framing and drywall i did not however see anything about electrical.  if the electricals all already ran or if your just prepared to use whats there thats great.  i would however suggest if its not or you cant wont be able to live with what you have get that electrical done before you do any sheetrock and insulation, or at the very least the wait on the sheetrock.   the electrician can if he has to work around the insulation though itll pry slow him down and he may charge you more for the job or even in the case of a time and materials the job could just take longer.  hopefully its all already done upto your standards and theres nothing to worry about but when i read your post i had a horrible vision as an electrician of standing in your garage going over the job with you and you telling me you need an outlet here and here and here and then proceed to mention how you just finished insulating, sheetrocking, and mudding the entire room with a beaming smile.  i just felt obligated to say something cause i dont want to end up possibly being that electrician 8-)  youll save money doing it now if it needs it vs paying for a more complicated and or more time consuming job later and not to mention you really should have it all brought upto code if its not already especially if your planning on selling soon cause the potential buyer will more then likely hire a home inspector whos in essence working for them and going to nit pick every thing he can thats wrong with the house and then they are going to use that as leverage to either have you fix it all or haggle with you on the price.  neither of which is to your advantage.  do it right the first time even if its just a couple outlets off the existing circuit thats already in place, let alone if you need any sort of dedicated or 220v lines, do it even if the panel is in the same area, it will just make everyones life easier and youll end up with the cleanest installation.  again i hope you have it all ready all done but just wanted to speak up just in case it was over looked.  take care, hope it turns out just like you want!

 

 

Nyles

  • Author

Nyles - thanks for the thoughts and comments. The electrical was done back when the garage was just studs. I had a sub-panel properly installed in the garage and then ran a few 220V and 110V circuits. It was quite reasonable to get it done as I had enough room in my main panel to add the breaker for the sub-panel.

 

The insulation is now all in. I used Roxul Comfortbatt's instead of fibreglass. I found it nice and easy to work with and worth the slight premium in price. I then put vapour barrier on the ceiling and walls. I then drywalled the walls. At the moment I don't intend to drywall the ceiling. It is very uneven and it would take a lot of work to put in strapping, shim it to make it even and then drywall it. I'm going to see how it goes with it just being insulated with the vapour barrier.

Thats great ottacat and what I was hoping, but I figured it would be better to say something now then later.  Sounds like its really coming together, when do we get to see some pictures? ;)

 

 

Nyles

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.