Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Polyurethane finish over shellac

Featured Replies

I'm building the 2 sheet bookcase & just about ready for pre-finishing. While looking at the directions on the can of Zinsser bullseye shellac it says it's not recommended for use under a polyurethane finish. Does the gel stain over the shellac create some sort of barrier layer for the topcoat? Marc didn't mention anything in the videos and seemed to have no problem with the final finish. Am I just reading too much into the can directions?

Thanks,

Dave

Finishing Rule #1:  Anything you read online is worth precisely nothing in the face of a real world test.  Round up the project offcuts and scraps (you have been saving them...right?) and try out your proposed finishing schedule.  Heck, try out two or three proposed finishing schedules and see which one you like.

 

That said, shellac is touted as a universal binder; so I'd be surprised if it gave you trouble.  It's even proposed as the binder layer between what would ordinarily be the worst case scenario for adhesion: applying a water-borne topcoat over any sort of oil.

 

Good luck.  Let us know what your tests show.

It sounds like you bought "regular"...what you'd use if you were going to build a finish entirely of shellac.  You should have bought dewaxed shellac...Bullseye SealCoat.  That's typically what is used for a first coat over oily woods or to prevent blotchy stain on blotch-prone species. 

 

You may or may not have issues with poly over it...Marc did a video testing out the conventional wisdom of not applying a poly topcoat over standard "waxed" shellac, and found that it didn't matter.  But that was just one test board...not exactly overwhelming empirical evidence, which he noted himself.

 

Why risk it?  Get the SealCoat.

Here's the video Eric mentioned: http://www.thewoodwhisperer.com/videos/shellac-under-polyurethane/

 

I used shellac as a sealer to help prevent blotching with the alder plywood I used for the bookcase. The first coat of shellac gets absorbed quickly and gets a nice sanding afterwards. So ultimately, there really isn't a whole lot of shellac on the surface when it comes time to apply the stain and topcoats. Between the tests I've done in the past and the fact that there isn't a lot of shellac in the mix, I have no problem using the standard Bullseye. Also, keep in mind that Bullseye Seal Coat doesn't come in the Amber or Orange variety. So if you're counting on that to add some color you'll need to pick up dewaxed shellac flakes and mix your own. 

 

Used in the context in the video, I have no problem recommending regular shellac. But like Rob said above, test on scrap. And also like Eric said, if you can get the dewaxed stuff easily, go for it. 

  • Author

Thanks for the feedback, that's very helpful.  I will now be entering the pre-test of finishes phase, before pre-finishing the project !

Dave

For what it's worth my standard finishing schedule over all my cherry is. 

1. coat of Bullseye amber shellac. 

2. sand 220

3. another coat of Bullseye amber shellac.

4. sand 320

5. 2 coats of GF Arm-R-Seal

6. sand 320

7-?. repeat 5 & 6 until you think you have enough coats. (3-4 for frames etc, 7-9 for small tables... etc...)

 

Of course your milage may vary.... but it's worked for me. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.