Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Maple Log into Lumber- Suggestions?

Featured Replies

Howdy all. Great forum here.

 

I've recently dropped a big western maple and I'm planning to have it milled later this summer. My goal is to use the lumber for kitchen cabinets in my house. I've milled maple before, mostly to make my flooring and I know how much it likes to move around, especially the figure wood. After my last mill run, I had a number of boards that came out of the kiln at >1" thickness and by the time I got 'em flat they were down around 5/8" to 3/4". This time I'm thinking that I should have everything come off of the mill around 5/4 to (hopefully) net 7/8. I'm also not sure about the legnth to cut the logs. Last time I was about 10' and that seemed like over kill for making any cabinets. I'm thinking this time to cut 7' (the big part of the log is 22') and have three saw logs.

 

I'm always trying to learn about this art, and find that other folks knowledge helps a lot. I'd like to ask you fine folks how *you* would cut this log, and what you would use the material for in your own shops. Project ideas, board size, legnths, anything you'd like to imagine.

 

Cheers from Western Washington State!

 

Joshua

I would be really interested to see what you come up with. Most log lumber I have purchased is from a through and through sawn boule . I would really like to have my own log quarter sawn for the extra stability and figuring it can offer but is a much more time consuming process as the diagram shows. Any movement that might then happens would occur evenly over the width.

54703d1352481649-quarter-sawn-quarter-sa

http://www.bobkloes.com

 

Send Bob and e-mail. Tell him Ace sent you. He is also a furniture maker but sells Hardwoods. He has various mills and loggers he deals with. Maples is his game!

Over the years I have purchase a lot of wood from him. He can help!

 

-Ace-

  • 5 weeks later...

I typically mill logs at 1 1/8 to finish at 3/4.  But if you get a lot of twisting, that is not adequate so I would go to 1 1/4.  Make sure you keep your drying stack level, lots of stickers between courses, a lot of air flow through the stack and a cover on top but not the sides to keep the water off it.  It is best to either put a lot of weight on top of the stack or band it during drying to keep it as flat as possible.  I've used those big zip ties to do short lengths of milled slabs and keep tightening them as the stack dries but that likely won't give you enough strength on a large stack.  It is also best to dry it slowly if possible.  I like to start milled stock drying in the very late fall and through the winter as the drying rate seems a lot slower then.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.