Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

What # cuts of shellac do you spray?

Featured Replies

I use Zinsser SealCoat somewhere along the line on most of my projects. Getting into spraying waterborne topcoats now I still want to use it but also don't want to cause problems. Is a 2# cut too thick to spray and will run, or will it cause problems under waterborne topcoats? Is a 1# cut good enough for sealing, barrier coat, and to magnify the grain on darker woods? I plan on using a 1.0mm set with my Fuji MM4 and want to do some practice spraying of shellac this weekend. 

Im not a shellac fan but seal coat sprays fine out of the can. 1# is fine for a barrier coat.  I use a .8 needle on most everything. An easier barrier coat is very thin lacquer or vinyl sealer, dries much faster than shellac.

==> Is a 2# cut too thick to spray and will run

 

#2.0ct is about as heavy as I ever spray...  As a seal/barrier coat,  I shoot a light coat of somewhere #0.5ct - #0.75ct Super Blonde -- I'm not too fussy -- it just depends on what I've got lying around....  If it's a light coat, I shoot it again to get some solids on the piece... I then scuff when I've got enough solids to work with...  If I'm going to build with shellac, then I shoot something between #1.5ct and #2.0ct (again, it depends on what I've got lying around) over the scuffed #0.5ct...  If the piece will have a shellac-only finish, then I build with a #2.0ct...

 

 

==> I plan on using a 1.0mm set with my Fuji MM4

 

Didn't think Fuji labeled their caps in mm (I have a conversion table someplace) ...  With a Fiji, I use the #3 cap set for shellac...

 

 

==> Is a 2# cut too thick to spray and will run, or will it cause problems under waterborne topcoats?

 

You'll have no problems with WB over shellac, but I don't shoot #2.0ct unless I'm building with shellac...  I'd shoot closer to #1ct for a barrier coat.

==> lacquer or vinyl sealer

 

PB's got a point, lacquer and vinyl drys super fast and vinyl sands back really well...  Shellac drys fast, but you've got to wait longer to sand back...  I simply use shellac because I've always got some already in a gun (or a PPS lid/liner) and it's a barrier to just about anything and everything...  It's also what I've got the most experience with, so that counts.. at least for me...

 

A further thought, shellac seems to permit a wider-range of environmental conditions... It's been unusually humid in the North East this year (average humidity for September was 84%RH --- that's really high for us), and shellac, for me, seems to tolerate wider %RH ranges than vinyl sealer-- but you still have to be careful -- once the %RH gets up there, you are going to have problems with most of what you shoot....

  • Author

I have 3 quarts of SealCoat so I will use that before adventuring into something else. I'll try a 1# to start and see now it goes. I'll have my PPS stuff tomorrow and will use that.

  • Author

Well I sprayed a 1# cut of SealCoat and it sprayed great and was dry in 15 minutes. I gave it 45 minutes to dry, sanded lightly with 400, and sprayed another coat and it took a good hour to fully dry. I think a 1# coat will be perfect for spraying - some schedules will only need 1 coat and others 2 coats. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.