Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Rikon 14" bandsaw and some resaw questions

Featured Replies

Hello all,
I recently purchased a 14" Rikon bandsaw and have cut (curved cuts) quite a good amount of wood, mostly plywood but also some laminated red oak. So far and not having any experience I am very happy wiht my purchase even though this is the version with the open stand, not the "delux" version. I have read that this saw comes with a crappy blade, however as a beginner in using a band saw it is hard to judge about that because I don't know any better.
Yesterday I tried resawing some oak wood. I setup my fence,used a feather board and cut some 3/16 thick pieces. No problems so far, same thickness on either side  however looking closer to the surface of the cut I realized that the surface is somewhat wavy. Not good because I wanna use these pieces to laminate a curved piece. Now I am looking for the problem and already can think about some factors which potentially could have an influence.

1. myself.... no experience
2. blade tension...
3. pushed the piece of wood to hard while cutting
4. the saw blade, maybe not really suitable for resawing

Initially I thought no problem, I will just do the pieces a little thicker and send them through my DeWalt planer... I tried.. unfortunately the planer wasn't to happy with such thin 13/64 pieces of wood. Better would be a drum sander... but I don't have one and I certainly wont get one only for that purpose.

 

Any suggestions?

 

Thanks Christoph
 

With my limited experience I always get "wavy" wood when rersawing. If the piece is too thin to run through the planer on its own you can use a planer sled to raise up the wood to the blade. If you search on the sites you will see how some do this. Just remember to not use nails or screws to attach anything to the sled that might hit your planer blades.

Resawing is something you want a good and sharp blade for.  However, even with a good blade, you will still need to use a planer or drum sander to cleanup as the band saw tends to leave a rough finish behind.

 

As Alberta Jim said, you can use a piece of MDF as a sled, double stick tape the piece to it, and send it through the planer to get your smooth side.

I have some questions!

1. How tall was the piece you cut?

2. how wide was the blade you used?

3. how many teeth per inch does the blade have?

4. have you set your fence to the blades drift angle?

With a sharp blade your cut should be nearly as clean as your table saw. The key to a clean cut is using your ears. The pitch should not change anywhere in the cut. Anytime there is a change in pitch there will be a saw mark. 

  • Author

Thanks for all your answers!

A rough cut would be ok, but mine is really wavy, I mean there is really a significant change in thickness along these waves.
With thickness of approx. 13/64 (W 2" L 20" ) the piece should no be to thin for the planer, according to the manual the DeWalt planer can go down to 1/8, but this is another problem and maybe needs some adjustment on the planer.

1. How tall was the piece you cut?  2"
2. how wide was the blade you used?  I haven't measured it but I think it's 1/4"
3. how many teeth per inch does the blade have? don't know...
4. have you set your fence to the blades drift angle?  Yes
 

==> The key to a clean cut is using your ears. 

 

Funny, I never really thought about it...

 

It's perfectly true -- and for many (most -- all?) of my stationary tools. I monitor jointing primarily by ear (secondarily by feel), same for planing, etc. Table saw is a combo of senses.

 

Like many things, it's so obvious once someone points-it-out to you...

 

Thanks...

2. how wide was the blade you used?  I haven't measured it but I think it's 1/4"

A 1/2" blade is much better suited for re-sawing on your saw. Basically for re-sawing you want the widest blade your saw can properly tension.

this is really important, because having to many teeth requires that you feed slower, and to few teeth can cause tooth loss. For 2 inch thick material I'd go with 3 or 4 TPI.

I have the closed base version of that saw; I upgraded the blade (from the stock blade) and it made a world of difference with the resaw performance.

If you don’t have a 1/2” x 3 tpi blade, go and get one. This will be a good blade for resawing and pretty much any other cut on a bandsaw except for a curve that’s too tight for a 1/2” blade. This is what I use on my bandsaw >90% of the time.

 

As far as your particular task goes, what I would do is to joint the face of the board, and then saw off a veneer. Use the jointed side to glue down the veneer, and then smooth out the saw marks however you like (sanding, scraping, rasps/files, hand plane). If you need more than one veneer, joint the sawn face again and repeat.

  • Author
Finally I got a 1/2" saw blade, not the greatest quality but I needed it fast and this was the only one for the 14" band saw they had on the shelf. However, as you said it really improved the quality of the cut. It seems to be not so noisy like the smaller blade with more teeth/inch and it cuts much easier/faster. There are still cut marks from the blade but the cut is a lot less wavy. 
 
Thanks for the help and happy holidays 
  • Author

That looks pretty good.
I could improve my cut quality about 50% only by using a wider blade. This is not even one of the advertised high quality blades, just the last one from the shelf for only 19$ or so.
Now it is time to get some practice and understanding of the process for further improvement.

==> That looks pretty good

To get results like PB, you need more than a fancy blade...

 

You need a well tuned saw, proper technique and a sharp blade... Doesn't have to be a fancy blade, but it has to be sharp... Getting a purpose-made re-saw blade will improve your results... But even the best blade won't help if your saw is not tuned and your technique poor...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.