Recommended Posts

Posted

I have a tormek T3 and the stone on it wobbles like there is something uneven somewhere throwing it off. I unscrewed and tightened and it still has a bit of a wobble to it. Possibly an uneven stone? Not sure how to describe it I will take a video when I get home though so it's easier to see.

Anyone had any issues like this before?

Posted

Not the bushings... I went through three wheels before I replaced the shaft/bushing on mine...

 

I'll download the manual and take a look for likely culprits... Assuming you Googled this?

Posted

Downloaded the T3’s parts explosion – the shaft/bushing assembly looks quite similar to the T7s – I really doubt that the bushings would go after 10hrs… Do you have the factory shaft assembly or the upgraded SS w/ EzyLock?

 

I’ve never seen a T3 wheel, but assume they’re like T7 wheels… Some T7 wheels have mounting holes that are close to the shaft diameter and some have inset bushings to reduce diameter. It’s never happened to me, but I read a thread where a wheel’s bushing came loose… Can you pull the wheel and check to see if there is an inset bushing and if it’s secure? That's my best bet... If it's not that, then check the runout on the shaft... Part of the Tormek's eligance is the simplicity of its design, there ain't a lot to go wrong...

Posted

I have done lots of work on tormek tools so after years of yes I am going to recommend you call the distributor for wh as t ever country your in I know they will resolve this under warranty

Posted

 

 

That is a lot of money for what should not be an issue on something with 10 hours and has had pretty close to the same issue since I got it.

 

Is that something guaranteed to fix this issue? I ask because if I spend $85ish on something and it still doesnt work I am going to be mad and feel I wasted that money when I need other actual tools.

Posted

After C's idea about the shaft, I rewatched the video a couple of times.. Could be the shaft assembly, but it's kind of hard to believe with only 10hrs on the unit... One question, was the T3 purchased new?... If so, I'll stick with truing the wheel... It's been years since I had my T7 apart (the upgraded SS shaft assembly has put a stop to annual maintenance)... If it's the shaft, then it could only be the bushing or (if the T3 is built like the T7), it could be the shaft retaining pin... But still, we're talking about something that would need hundreds of hours to start showing signs of failure... If it was defective from the factory, then you'd see it right away... A final test... Mount the camera on a tripod, focus on the side of the wheel and lightly keep the chisel at the outside -- we'll then be ably to see if there is a side-to-side wobble, or just an out-of-true wheel... I'll double-down on out-of-true...

 

Note: The MSK-250 SS Shaft is a very worthwhile upgrade... I was replacing shaft/bushings with every wheel, but havent had to change the shaft in at least four years... Worth the $60. I've never seen the MSK200, but suspect it's just as good.

 

As for being bushwacked, that might not be too far from the truth -- you need a truing tool right out of the box. For the $$, many have argued that Tormek should provide one with the unit, but they don't... Sort of like the Kapex should come with the crown molding accessory, but that's another rant for another day :) ... I've warn-through four or five wheels and they all need truing out-of-the box and about every hour of use (depends on how heavy the use, the grade of stone and what type of binder)... Sorry, that's just the way it is... Many who struggle with the Tormek don't even know to true the wheel, much less that it has to be done frequently... I haven't read the manual in a decade, but think they used to recomend re-truing after every tool -- do they still do that?

Posted

The 250 says its for the t7 ... I have the t3. Is it backwards compatible?

So if I can only buy one of these .. The shaft or truing mechanism .. What should I try first until I get some more money?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   2 Members, 0 Anonymous, 60 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined