Recommended Posts

Posted

I've had my Grizzly G0500 8" jointer for about 2 yrs now. I bought it off craigslist and it worked perfectly ever since I brought it home.

I noticed that the blades were getting dull, so I tried to use a hone to sharpen them in place on the jointer. I'm sure that you have seen these little hones for sale at various sites.

Well somehow I royally screwed up my jointer, because after that, I could not get a straight flat board. Not even close.

So I started looking around to find new jointer knives. I finally settled on InfinityTool knives over Holbren, Grizzly, etc. They cost much more, almost twice as much, and I figured that you get what you pay for, and for me, all projects start at the jointer. If your boards are not straight and flat, you will have problems the whole way thru the project.

I have never changed or set knives before, but I have read many blogs and forums and magazines and watched videos. But I was still apprehensive.

I received my knives from Infinity, and when I looked at them, the bevel was very roughly ground. Not shiny at all with very deep scratch marks. I figured if this is the way they ship their knives to their customers, it must not matter what the bevel looks like, so I proceeded to set them.

After all my research, I decided I didn't need a fancy jig, so I just used a dial indicator on a magnetic base.

On the first knife I found it impossible to get a good reading because the edge of the knife had so many humps and valleys, that the dial indicator would jump .003 (not in the length of the knife) but within every 1/2" as I slid it along the knife edge.

I concluded that I just got a bad set of knives that somehow slipped thru their quality control. I emailed them and they offered for me to send them back and after looking at them, they would decide if they were faulty or not, and make a determination on what to do about it at that point.

I have a project that I need to finish by Thanksgiving and could not wait for that process to play itself out.

I honed all the backs of the knives with a 4000gr stone, and very lightly ran that stone on the bevel, and eventually the roughness disappeared.

I proceeded to set all 4 knives and was surprised at how easy it was to get them all dead flat with the outfeed table.

I now get smooth flat and straight boards from my jointer, but I thought that I would post my experience here to inform others.

I would recommend buying your jointer knives from another source, because you don't always get what you pay for.

Jim

Sent from my iPhone using Tapatalk

Posted

I've had my Grizzly G0500 8" jointer for about 2 yrs now. I bought it off craigslist and it worked perfectly ever since I brought it home.

I noticed that the blades were getting dull, so I tried to use a hone to sharpen them in place on the jointer. I'm sure that you have seen these little hones for sale at various sites.

Well somehow I royally screwed up my jointer, because after that, I could not get a straight flat board. Not even close.

So I started looking around to find new jointer knives. I finally settled on InfinityTool knives over Holbren, Grizzly, etc. They cost much more, almost twice as much, and I figured that you get what you pay for, and for me, all projects start at the jointer. If your boards are not straight and flat, you will have problems the whole way thru the project.

I have never changed or set knives before, but I have read many blogs and forums and magazines and watched videos. But I was still apprehensive.

I received my knives from Infinity, and when I looked at them, the bevel was very roughly ground. Not shiny at all with very deep scratch marks. I figured if this is the way they ship their knives to their customers, it must not matter what the bevel looks like, so I proceeded to set them.

After all my research, I decided I didn't need a fancy jig, so I just used a dial indicator on a magnetic base.

On the first knife I found it impossible to get a good reading because the edge of the knife had so many humps and valleys, that the dial indicator would jump .003 (not in the length of the knife) but within every 1/2" as I slid it along the knife edge.

I concluded that I just got a bad set of knives that somehow slipped thru their quality control. I emailed them and they offered for me to send them back and after looking at them, they would decide if they were faulty or not, and make a determination on what to do about it at that point.

I have a project that I need to finish by Thanksgiving and could not wait for that process to play itself out.

I honed all the backs of the knives with a 4000gr stone, and very lightly ran that stone on the bevel, and eventually the roughness disappeared.

I proceeded to set all 4 knives and was surprised at how easy it was to get them all dead flat with the outfeed table.

I now get smooth flat and straight boards from my jointer, but I thought that I would post my experience here to inform others.

I would recommend buying your jointer knives from another source, because you don't always get what you pay for.

Jim

Sent from my iPhone using Tapatalk

   My experience has always been, that when you purchase a tool that has a sharp edge, No matter what the seller  tells you, HONE!

Posted

Richard, even jointer and planer knives? I really have no way of honing those except for the way I did, just touching them up. I've seen jigs but I never though that I could do a good enough job. I think jointer and planer knives should be ready to install, unlike chisel and plane irons which I know need honed.

Sent from my iPhone using Tapatalk

Posted

Richard, even jointer and planer knives? I really have no way of honing those except for the way I did, just touching them up. I've seen jigs but I never though that I could do a good enough job. I think jointer and planer knives should be ready to install, unlike chisel and plane irons which I know need honed.

Sent from my iPhone using Tapatalk

 

Touch up planer, jointer and moulder knives on the back side. Let a professional grinder handle the edge. Its to easy to screw up a perfectly good knife.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   0 Members, 0 Anonymous, 47 Guests (See full list)

    • There are no registered users currently online
  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined