Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

New Shop feedback

Featured Replies

Hi all!

 

This is my first post here at WoodTalk. After reading a lot of discussions and seeing the wealth of experience and good information I was hoping to get some feedback on my planned shop. I have been woodworking on the side for several years but took the plunge last year and started my own business in hopes of making a living on my woodworking. In order to do so, I need to get out of my now extremely small shop and in to a little less small shop. Due to local regulations and insulation need (I live in Sweden) the interior space is 25x18. Yes, I know, bigger is better, but I am not allowed to build bigger. Height is just over 8' at the long walls, and just over 12' at the middle of the building.

 

Due to my location, I also need to make sure that sound does not escape, potentially resulting in unfriendly neighbors.

 

  1. The jointer pictured will be a combination jointer / planer
  2. There will be a place for my “office” with a computer
  3. The table saw (hopefully a Sawstop) will have my current contactor saw “integrated” to the right of the blade so that I can use the fence for both saws. This way the contractor saw can have a dado blade installed at all times.
  4. Clearvue cyclone mounted as close to the ceiling as possible.
  5. Two shop built sys-ports for most of the Festool systainers under the windows (less noticeable from the outside).
  6. Compressor mounted in a box on the wall with pipes to distribute air where needed.
  7. Clamp rack on the wall next to the band saw.
  8. Hand tool storage on the wall over the bench/storage cabinet to the left of the “office”
  9. Planning on building a Roubo workbench
  10. Extra “storage rafters” over one side of the shop for more long term wood storage.
  11. Heater will be on the wall to the right of the cyclone.
  12. One entry door and two carriage doors. They will actually be double doors to keep the sound from escaping.

 

I would appreciate any and all feedback on my layout, and please ask if anything is unclear.

 

Thanks and a happy new year!

 

Göran

 

 

post-16636-0-55188400-1420191047_thumb.jpost-16636-0-38207500-1420191050_thumb.jpost-16636-0-80802600-1420191052_thumb.j

  • Popular Post

Hey Goran, welcome to the forum.

 

Those shop layout programs are fun to play with and good for giving you some general ideas, but I found that what looks perfect on the computer doesn't usually translate in physical space.  You'll end up moving things around several times, I guarantee it, and that's just par for the course.

 

Since you'll be doing this for a living, efficiency will be key.  The one perk of having a small shop is that nothing is too much of a walk to get to.  But you'll still want to arrange your shop with workflow in mind.  Maybe try clustering your joinery machines closer together...perhaps swap the jointer for the bandsaw and move the miter saw to between the sink and sheet goods?

 

You'll do a few projects in your new space and realize snags in your workflow.  And you'll make changes and adapt.  Again, and again, and again, until you're running smooth as silk.  I enjoyed the evolution...my major shop changes are pretty much over, but it was a fun and challenging process balancing shop space, organization, and efficiency within my particular set of parameters.  Every shop and every woodworker is different, so it's pretty much impossible to give you the "perfect layout."

 

Good luck!

You are probably going to need to turn your table saw the other way. Your shop is only 18 feet wide. I am assuming that is an outside dimension? If so you don't have enough room for an 8 foot sheet good and you holding it. If its an inside dimension, you still don't have enough room to do it comfortably. Similar problem with the jointer with pieces running into other bits of machinery unless you are only going to work with small stock.

Setting up a dedicated dado stack station improves efficiency, but a combination machine for jointing and planing reduces it... unless you are dealing mostly in plywood. I have the Jet JJP12-HH, it's an excellent machine, but if I had to do the changeover multiple times a day just to get my work done, I think it would start to get on my nerves.

 

You might find this article from Fine Woodworking a good read.

  • Author

Eric.

Thanks for your input. I plan to keep as much as I can on moble bases so that I can rearange when needed. The layout of the ducting for the DC will also be expandable so hopefully it will be fairly simple to change the setup as things evolve.

 

Apple Wood.

18 feet is the inside dimension (25x18). The plan is to cut down sheet good using my track saw (on a few 2x4 on the floor in front of the tabel saw). I also plan to keep the tools mobile, so if needed, I can move the jointer/planer and open the carriage doors so that I can process longer pieces.

 

Thanks for your input!

  • Author

Cabinfever.

Yes, the combination machine is a bit more work, but as I have limited space, it feels like the best option.

I read the article just a few days ago, thanks!

I'm not so sure you will be able to get a Sawstop in Sweden as they don't appear to be exporting to Europe yet. You may be able to import yourself privately but won't get the support that a dealer gives. As far as I am aware they don't meet EU regs yet either. It's only a matter of time of course before they do meet regulations though.

The shop layout you have is good for a start just to see if you can fit all the equipment in. As others have said it will evolve in time and you will end up moving things around here and there. Good luck with it and hope to see you more on the forum and see what you come up with,

  • Author

TerryMcK.

You are right about the sawstop, I need to import it using a shipping company that can handle all the logistics, customs, etc. It´s a bit of a hassle, but in the long run I figure it is worth the time and money. There is also extra work and money for a frequency converter pushing the electricity up to 60hz, but that will be needed for the Clearvue cyclone anyway.

You might want to combine the function of the MFT into an outfeed table, something like this.

 

You don't seem to have a router table anywhere, wouldn't a router on the side of the table saw be more versatile than a second saw for dados and grooves? Seems like you'll be taking the stack on and off anyway to adjust shims, so a dedicated station might not be much of a timesaver. Not to mention if you are getting a SawStop, why not take advantage of the safety features for dado cuts as well.

  • Author

Ahh, I forgot to mention the router table. I have a shopmade one right now, but it is not really up to par. One solution that I am considering is the Festool router table extension for the MFT. With an OF2200 it seems like a good and powerfull solution, possibly with an incra fence for better accuracy. In an earlier layot I had the MFT with the router extension as an outfeed, but I am also thinking about the new slider for the Sawstop, so that solution became a bit strange. I use the MFT quite a bit, so it is always set with the guide and rails for the track saw, so I think they will get in the way if I where to use it as an outfeed table. One problem is that with the extension, the MFT might come a bit to close to the band saw, I need to think about that a bit. Any suggestions?

 

I agree that the safety features for the dado blade as well, and I think I will get that as well. For many operations that I do, I use the same width on the dado blade, so it is hopefully quite usefull with a fixed setup. If not, I can always change my mind! My idea is to modify the saw that I have so that it can be bolted to the Sawstop, so if I change my setup, the Sawstop will be unharmed.

 

Thanks for your input!

If I was going to spend $2k on a router solution, I'd get a shaper. I know people love Festool, but if you don't need the portability, I think a Laguna Compact Shaper would be much more versatile in a pro shop for the money spent and can be more readily fitted with a power feeder.

 

Plus it will be much quieter.

  • 2 weeks later...
  • Author

I have updated the layout by adding a router table (shop made) just inside the carrige doors. I also moved the drill press next to the router table and places a combination sander (might turn out to be some other sanding unit) in the corner next to the jointer/planer.

 

The router table and the drill press will be on casters so they can be rolled out of the way when I need to use the doors.

 

Any thoughts?

 

By the way, what would be the best setup for dust collection at the router table? I have two possible solutions, one is to reduce the DC pipe and use the cyclone, the other is to use a Festool vac. Any ideas on which would be best? I plan to split the hose so that I can collect both under the table and at the fence (thinking of an Incra fence).

 

Thanks!

post-16636-0-27455400-1421264726_thumb.j

If you are going with combo jointer/planer maybe look into getting a small, inexpensive lunchbox planer for when you need to thickness something and your combo machine is set up as a jointer. Honestly I could think of plenty of times when it would be nice to have two planers. If you are building a piece with multiple thicknesses you could keep them both set to different thicknesses. On most planers, once you change the thickness it is difficult to get it back to exactly where it was.

Also I don't see any stationary sanding machines. If I were a pro I would definitely have a drum sander. I use my oscillating spindle sander all the time. Anything you can do to make your sanding more efficient is worth the $, in my opinion.

When I bought my stationary planer I thought keeping the lunchbox around would be a good idea but I never ended up using it and sold it. A Wixey on your planer will allow you to make future boards an exact thickness.

  • Author

If you are going with combo jointer/planer maybe look into getting a small, inexpensive lunchbox planer for when you need to thickness something and your combo machine is set up as a jointer.  Honestly I could think of plenty of times when it would be nice to have two planers.  If you are building a piece with multiple thicknesses you could keep them both set to different thicknesses.  On most planers, once you change the thickness it is difficult to get it back to exactly where it was.

 

Also I don't see any stationary sanding machines.  If I were a pro I would definitely have a drum sander.  I use my oscillating spindle sander all the time.   Anything you can do to make your sanding more efficient is worth the $, in my opinion.  

Thanks for the tip! I will start with the big unit and if the need arrises, it is easy to add a lunchbox planer. The big unit will be a hefty investment, so I need to keep the budget under controll...

 

I have a drum sander on my secondary wish list... the day I can no longer get by with what I have, then the drum sander will move to the first wish list!

  • Author

When I bought my stationary planer I thought keeping the lunchbox around would be a good idea but I never ended up using it and sold it. A Wixey on your planer will allow you to make future boards an exact thickness.

Is it a straight forward operation to attach a Wixey?

I've attached a similar one to mine. Ten minutes work. Mine works off the rotation of the winding handle counting the number of revolutions. There is a direct correlation between one turn and distance moved. 

Some digital ones like the Wixey Planer Digital simply have an anchoring point that fixes to a non moving part of the machine. The other end attaches to the moving platten part and measures linearly. 

There are instructions on how to mount their gauge on their website. 

 

Either gauge is really easy to calibrate. You simply just randomly plane something. Measure its resulting thickness and then set the readout to the same figure. Job done.

From then on you after taking most of the waste down to thickness you can set the final pass dimension to what you want to achieve and the timber that emerges is to that figure.

 

Here is my purely mechanical gauge measuring in millimetres

IMG_0499.JPG

Here is what I have and it was easy to install. If I need to mill a board to exact thickness I'll lower the table a few turns past the value I need then switch directions. There is some play in the wheel and always reading while going the same direction helps.

 

http://www.wixey.com/remote-planer/index.html

  • Author

I do custom furniture as well as bigger built ins. The bigger projects I prepair in the shop and assemble on site. I am a one man show trying to design a setup that allows me to perform as many different tasks as possible. The idea is also to make the shop reasonably nice looking so that I can invite customers to the shop.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.