Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Grizzly Fence Retrofit to Jet 14" Bandsaw

Featured Replies

When I bought my Jet 14" bandsaw 15+ years ago, fences weren't a standard item or even easy to get. For years, I got along with an L-shaped fixture, but got tired of aligning it each time I wanted to move it. I looked through the recent 14" bandsaw reviews in FWW and noticed that they had good things to say about the Grizzly fence. After researching, I found two fences, one for 14" and another for 17" saws. The 14" saw said it was for a 14" table and the Jet is a 15" table, but the next size up looked like it would hang out in space too far. I liked that the aluminum extrusion could be placed in the tall position for resawing or flipped on its side for a short fence. Because the extrusion attachment is use a T-track, I can make other attachments. I liked the fence, so I requested the 14" fence from Santa Claus and found it in my Christmas stocking.

Installing the front and rear rails was trivial - 2 bolts each. I pulled the fence out of the box and placed it on the front rail, but it didn't sit flat:

56d34f1ec401e_Fencesupporttooshort.jpg.b

I kind of expected that. I originally hoped that I could just remove the support button and let it ride on the table, but if I wanted to make a cut wider than the end of the table, the fence wouldn't be supported. Time for a fix. I took the fence apart to see how things were done. The stock support button screwed into a hole that was tapped into a cast iron rib on the main support bar:

56d34f993c596_StockSupportButton.jpg.f84

56d34f6fd5fb7_StockSupportButtonHoleLoca

Time for surgery. I marked a line 1/4 inch up from the bottom of the bar and for about 2 inches in from the back end. Using a hacksaw, I cut down the line:

56d34fdf7fe47_HacksawCuttingMainMember.j

Having a good hacksaw that holds the blade tightly and tensions the blade properly really helps here. After cutting the piece out, it looked like this:

56d35061a8b3f_FinishedCut.jpg.9e994d6dfe

A little touch-up with the disk sander cleaned up the cut line. Using a piece of 1 1/2 inch wide x 1/4 inch thick steel, I cut a piece that extended past the end of the main support member about 1 inch. I drilled a through hole to accept a screw to mate with the original hole in the main support member and countersank the hole. I drilled another hole so it would center on the rear rail and tapped it for M6-1.0 to match the threads on the button:

56d3511bacf75_NewButtonSupportPiece.jpg.

You need to be careful that the new plate won't interfere with the aluminum extrusion when installed. A quick coat of paint and I put everything together:

56d35158bd888_NewButtonSupportInstalled.

Mounted back on the saw, everything lined up correctly, the fence sat down near the table like it should:

56d3519b032a1_NewSupportInstalledFencein

The fence locks down tight and holds its settings. I can make small adjustments easily for resawing veneers. Finally, I needed something to hold the fence when I'm not using it. It is heavy and won't lean neatly against the bandsaw. I used some scrap plywood to create a holder for the fence:

56d357357f577_FenceHolder.thumb.jpg.2fea

The piece on the right is necessary to keep the fence from falling out of the holder.

I am happy with this setup. So if you are looking for a fence for your 14" bandsaw and the table is deeper than 14", this modification works well and it only took about an hour to do.

Very nice.  I have the same fence and I am going to steal your holder idea.:ph34r:  thanks.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.