Recommended Posts

Posted

I'm attempting to apply some Stone Wall Tiles (each tile is 5.6"x 23.6") to a kitchen wall that is approx. 8'x 9'.  I had planned on picking up a bag of Ultraflex Tile Mortar but was advised by the Kent store employee that Lepage PL Premium X8 construction adhesive would be the best way to install these tiles.  Can anyone comment on this?  My initial plan was to use 1/4x1/4 square notched trowel, apply the mortar to the wall and put the tiles up.  The PL adhesive would certainly be less of a mess and the label on the adhesive claims that it is recommended for vertical wall tile applications. Anyone have any experience with this?  I'd prefer to do this right the first time!!

 

Thanks...  

Posted

Eilther will work, but thinset will be a lot cheaper, and probably even hold the pieces in place better to start with.  I think that particular construction adhesive is close to 8 bucks a tube, and one tube won't go far for that job.  It's very sticky, but doesn't hold things in initial position as good as PowerGrab.  I've bought, and used, more than a few cases of each. Also, X8 expands a little as it sets, which is a bit unusual for construction adhesives, and probably would not help you on this job.

If you use thinset, I'd use a bigger notched trowel than 1/4".  That's more for small wall tiles that are very uniform for thickness and flatness of the backs.  I'd use 3/8 or maybe even 1/2 depending on how flat the backs are. Stiffness of the thinset mix will be important to get right.  You want to be able to spread it, and it has to be wet enough to be sticky to the tile, but you don't want it to slump on the wall by itself.

Get a package (or several) of the little plastic wedges in case they want to slide down.  The wedges can be used under the bottom row, as well as between pieces to maintain space between the pieces for grout.  They pull right out after the thinset has cured, and can be reused many times.

Posted (edited)

Thanks for the response and information.  This particular type of tile has to be installed  without any spacing, there's no grout involved.  The back of the tiles are not flat as they  are small rectangle pieces of stone of varying sizes and thicknesses glued together.  Due to the fact that they are not flat, would I need to apply thinset to the back of each tile or can I just apply the thinset to the wall and install each tile? I've attached a pic of the stone tile.

 

 

800x197_products_info-image-185684.jpg

Edited by NLwoodworks
reinstalled pic
Posted

Back buttering can be a pain.  Just buy the cheap trowels.  You might need to get a couple to find the right notch size by trial.  Spread thinset on one section of the wall, press a tile into it, pull it back off, and see how the coverage was.  If you can get full coverage with any trowel, I would do it that way.  You will definitely need a bigger notch than 1/4".  The smallest notch that will work is best.

If you can't easily get full, or close to full coverage with just the trowel on the wall, then you will need to back butter.  Get at least one of the small rectangular margin trowels to have to taper the thinset back on the edge of a tile.  http://www.homedepot.com/p/Marshalltown-5-in-x-1-1-2-in-Margin-Trowel-54D/203221341?cm_mmc=Shopping%7cTHD%7cG%7c0%7cG-BASE-PLA-D22-Concrete%7c&gclid=CjwKEAjw8bO3BRDp0bP_vL-7_lASJACL_d6w3qsEDYBsVL0zXklV7-ZeEC2-KN2vtUQ9j75QbQ0tVBoCOfLw_wcB&gclsrc=aw.ds

You might also need one in the bucket of thinset.  I can't think of any tile job I would do and not use the little margin trowel. To back butter, place mud on the tile back with the rectangular trowel, and spread it around with the notched trowel.

You will also need at least one bucket of water, and a couple of good sponges.  You need to clean any thinset off the exposed surface before it dries.  If you can keep the faces clean to start with, it will be many times better.  First use the rectangular trowel to taper back the edges, cutting away the extra mud, and then clean the edge with a sponge, but not dripping wet, before putting that time on the wall.

I still get the little wedges.  Perfect joints may well require the first row to be pushed up here and there to make the joint between it and the second row perfectly straight. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.