Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

grizzly G0715P vs delta 36-5100 vs rigid r4512

Featured Replies

20 minutes ago, Cygnus A said:

I will chime in. I purchased the G0715p last September. Long story short, it is going back this week. The alignment problem still exists. I spend hours on multiple occasions trying to align the damn thing only to discover the blade kicks out of alignment whenever you raise or lower it. 

That's a shame..  I've had great luck with mine but, it goes to show that sometimes you get a lemon!  Best of luck with your next saw!  It's a PITA to deal with this stuff when it happens!

Gah.  It was quite the ordeal moving my 715 from the driveway, through the yard, into my basement, and getting it setup by myself.  With so little time nowadays, sending it back would be a nightmare.

I thought mine was good, but looking back to the setup, I had it dialed in then realized the drive belt tension was way too loose.  I lowered and raised the blade several times just to get a visual on the belt.  Got the belt tightened up, then had to re-do the alignment process.  I assumed it was from adjusting the motor/belt tension, but now that I think about it that doesn't make sense.

 

On ‎5‎/‎15‎/‎2016 at 1:29 PM, bleedinblue said:

Gah.  It was quite the ordeal moving my 715 from the driveway, through the yard, into my basement, and getting it setup by myself.  With so little time nowadays, sending it back would be a nightmare.

I thought mine was good, but looking back to the setup, I had it dialed in then realized the drive belt tension was way too loose.  I lowered and raised the blade several times just to get a visual on the belt.  Got the belt tightened up, then had to re-do the alignment process.  I assumed it was from adjusting the motor/belt tension, but now that I think about it that doesn't make sense.

 

Do you have a dial gauge? If so, place it at the rear of the blade. Lower and raise the blade and you will probably see what I did. The rear of the blade shifts while the front does not. Thus alignment is lost whenever you change blade positions. I only notices this AFTER performing an alignment and my wood started burning/getting stuck between fence and blade.

You can do it without a dial gauge by placing a straight edge along the blade while raising/lowering. You will see a gap at one end when doing this.

I feel your pain. I disassembled the saw yesterday and now am building a crate to send it back. Part of me just wanted to keep the saw and deal with it, but $800 for something that is not working like it should was something I couldn't justify.

Yeah, I'm using a dial gauge.  The other night right before I made that last post I put the indicator on the front, middle and rear of the blade and raised and lowered it.  I was getting inconsistent results, but the blade did seem to be shifting around 5-8 thou.  I don't remember which position was the worst, but each shifted slightly and they weren't all the same. 

As the others noted, I'm going to use the saw a bit and monitor it.  As it sits right now it is waaaaaaay more in alignment than my old saw was.  If the problem gets worse, I'll suck it up and call Grizzly.

It makes me wonder if I should have gone with the cheaper 771, which (I think) has cabinet mounted trunions, so it has a different construction that probably doesn't have this problem.  The fence of the 771 could have been upgraded.  If I end up having to return this saw, I'll explore that option more closely.

54 minutes ago, bleedinblue said:

Yeah, I'm using a dial gauge.  The other night right before I made that last post I put the indicator on the front, middle and rear of the blade and raised and lowered it.  I was getting inconsistent results, but the blade did seem to be shifting around 5-8 thou.  I don't remember which position was the worst, but each shifted slightly and they weren't all the same. 

As the others noted, I'm going to use the saw a bit and monitor it.  As it sits right now it is waaaaaaay more in alignment than my old saw was.  If the problem gets worse, I'll suck it up and call Grizzly.

It makes me wonder if I should have gone with the cheaper 771, which (I think) has cabinet mounted trunions, so it has a different construction that probably doesn't have this problem.  The fence of the 771 could have been upgraded.  If I end up having to return this saw, I'll explore that option more closely.

Interesting. So yours is shifting but remaining parallel to the miter slot? Mine was not. Only the rear was shifting and by up to .030"

No, it's going out of parallel, just not a lot.  I adjusted it with the blade at its highest, and when I lower the blade as far as I can while still getting the gauge on it, it's about 5-6 thousandths difference.

  • 9 months later...

I am a small contractor. Beside of typical home improvements like bathroom/kitchen remodeling I do make custom size/shape cabinets, entry doors, bookshelves and some custom trim work.

So, my experience with Delta is very upsetting. The customer support is very poor, it is a big issue if you need to order parts or repair your saw. I've dropped my saw at Authorized Equipment Service at Memphis, TN on November 16, 2016..... Well, at February 12, 2017 the saw was still at that repair shop.

My saw has cast iron extension wing that wasn't flat out of the box with 1/32-1/16 difference between sections that result in 1/8-1/4 difference between those sections. Pretty big blade vibration that makes you to sand every single cut. On the top, the dust has significant design flaw. With shop vac attached to the saw my head and t-shot are covered with saw dust! What else to say...? Out of the box every single part was out of square. I mean everything; the blade, the miter slide, the fence, etc.

Honestly, after trying to deal with Delta customer service and local Delta authorized repair shop I will not buy anything made by Delta. If you spent over $1200 on a tool and it is at the repair shop for over 80 days during the very first year...... I did learn my lesson hard way. Don't make my mistake, just try to call Delta customer service BEFORE YOU BUY any tool with name Delta on it and see for yourself how poor support you should expect if your tool needs service/repairs.

Photo #4.jpg

Photo #1.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.