Pwk5017 Posted June 16, 2016 Report Posted June 16, 2016 I might have asked this previously, but im about to pull the trigger on a table and want reaffirmation. Any regrets from current owners? Seems like the fence leaves something to be desired, but the QWAS dogs and rail dogs could be a good Plan B if the fence sucks. Im buying this for the shop and for future home remodel projects. Seems like it will be "meh" for the shop and great for off-site work. Quote
mkrusen Posted June 16, 2016 Report Posted June 16, 2016 Its a very nice addition to the shop. Yeah it seems like the fence comes out of alignment fairly easily but its super easy to adjust so I just double check it before I start. Of course it would be great for off-site work but mine never leaves the shop and I love it. It is my go-to tool for large crosscuts. Quote
Woodenskye Posted June 16, 2016 Report Posted June 16, 2016 I like mine, but if you are going to use as main workbench you may be disappointed. I bought the cross supports and they help, but I also added a shelf which I have stuff on, which always me to do some hand tool stuff like using hand planes. The fence is fine, and really easy to adjust. I took a sharpie once I got it square and traced the fence profile. The clamping options and dog options are great. Lee Valley makes a MFT clamping set that is pricey, but very nice, I bought when first introduced, so price was probably better than now. The following product is great to eliminate any slop in the rail. https://www.festoolproducts.com/Tool-Improvements-Slop-Stop-for-Festool-MFT-Tables-p/ti-ss.htm Quote
Nestor Posted June 16, 2016 Report Posted June 16, 2016 I sold mine, along with the fence, rail, and a couple of clamps. Festool is a "system" as much as it is a set of power tools, and I found switching back and forth between my TS and the MFT to be cumbersome. I was also cutting sheet-goods wider than what the MFT could handle. I've been much happier after adding the slider to my Sawstop PCS. Don't get me wrong. I still have my TS55 saw, rails, and a Kapex, but I just couldn't get the MFT to fit into my work-flow. YMMV. Quote
Pwk5017 Posted June 16, 2016 Author Report Posted June 16, 2016 Funny, I had the jessem mast r slide on my saw(pretty much identical to the ss slider), and i ended up selling it because i was crosscutting massive things. This is where the track saw came into play. It is easier to true up a table top panel with the track saw, than it is to lift a 120lb 8' panel onto the slider carriage and make the cut. It was a sweet setup for repetitive crosscuts(end grain cutting boards), but i never got it dialed in for truly perfect crosscuts. Something was flexing through the cut or something, because my crosscuts were never dead nuts perfect. I want the MFT for off-site work, and to handle the tweener crosscuts that my miter gauge is too small for, but arent big enough to justify setting up sawhorses with guide rail and clamps. I have a traditional roube-esque bench for 95% of my work holding needs. The MFT will only be for guide rail use with the 1400 or TS75. It is also another horizontal surface for collecting clutter. Quote
kixnbux Posted June 18, 2016 Report Posted June 18, 2016 No regrets. Mine usually only goes on site on multi day remodel jobs though. I don't set all up for a half day. Usually just throw down 2 inch foam and roll with TS55. But on multi day it's handy. For doing pocket hole work. Frame assembly. Anything really Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.