Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

NordFab Ductwork Sizing

Featured Replies

I just installed a ClearVue CV1800 cyclone.  I contacted NordFab and was referred to my local dealer.  The dealer has designed as system that has a 6" trunkline going to my lather and 4" thereafter.  It seems that Mark and every other internet guru continues the 6" as far as possible before necking down to machine port size.  The designer for my system says that is inappropriate and the system will not maintain CFM at the larger diameter.  Any thoughts?

Nordfab has a design service, I'm not sure why they would refer you to a local dealer.  Ultimately, the answer to your question is determined by how many drops you have and what the distance is.  I used their design service and ended up with a 7" main trunk line.

Welcome to the forums.

  • Author

I did contact Nordfab for design and they referred me to a local dealer, EAS. Perhaps it was because I am on the West Coast. My longest run is to my miter saw, about 30 feet. But she necked the trunk line down to 4" immediately after the lathe drop, about 6'. Only one machine will be running at a time.

I'm on the West Coast as well.  Contact Clear View and ask them for design assistance.  

I only run one at a time as well.

  • Author

After much discussion with EAS, who claim to have consulted Nordfab, they have offered to install 6". However, they claim, the CFM from the ClearVue is not guaranteed to be sufficient to clear the duct. They believe I'll have a build up of dust in the ductwork. I believe they're sincere in this since they'd make more money with the 6" system. Could they be right?

All I can tell you is I just removed the old system which was 6" hvac snap together with lots of leaky adjustable 90's and at least 1 T from the stove pipe section (def. no-no :) ) as well as having the crimps facing the direction of airflow. Also, the cyclone is a 2 HP  Grizzly so much less powerful than yours. 

I found no significant chip buildup when I broke it down. There were some chips jammed between the crimp and the pipe here and there. And, there was one section of pipe which is little used to my band saw. It did have 3 or 4 cups of chips run out the end when I pulled down a 10 foot section. That branch had not been used in months and the little bit there bounced around a corner away from the cyclone from the main where the planer is. 

Just open the gate on the unused branches once in a while, WHOOSH, away goes any buildup.

One other thing, have you specifically told em this is a one man shop? Commercial designers will assume all machines with gates open sometimes. 5 guys in a cabinet shop don't take turns :).

It sounds like they are trying to maintain same CFM everywhere, including the 6" duct before your branches, which would imply that you have to run at least two 4" drops all the time.

Are all of your tools using 4" connections?  If so, then they are probably right in that the section of pipe between the tool connection and the brach may not flow well enough.  Personally, I would make every attempt to use either a single 5", or single 6" or 2 x 4" connections to every tool, so you can keep 6" drops and main line.  If a tool only had a 4" connection and you cannot make it bigger, see if you can either (1) hook up 5" anyway or (2) add a 2nd 4" connection for "auxiliary" collection, like overhead pickup for you table saw or band saw or router table.

  • Author
2 hours ago, andrew-in-austin said:

It sounds like they are trying to maintain same CFM everywhere, including the 6" duct before your branches, which would imply that you have to run at least two 4" drops all the time.

Are all of your tools using 4" connections?  If so, then they are probably right in that the section of pipe between the tool connection and the brach may not flow well enough.  Personally, I would make every attempt to use either a single 5", or single 6" or 2 x 4" connections to every tool, so you can keep 6" drops and main line.  If a tool only had a 4" connection and you cannot make it bigger, see if you can either (1) hook up 5" anyway or (2) add a 2nd 4" connection for "auxiliary" collection, like overhead pickup for you table saw or band saw or router table.

That is exactly their point. The tools are all 4" (and a few 2 1/2"). Most of them would be difficult to increase to 6" (or double up at the tool. Thanks. Somehow your explanation made more sense than theirs.

So I think I'll go with a 6" trunk line with 4" or 5" drops.

 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.