Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Craftex CX404 1hp dust collector

Featured Replies

As some of you may know, I've been somewhat lacking in the dust collection department. As in I have none, except for a decent shop vac with dust deputy setup. I've managed with that, but the Roubo finally made me start thinking seriously about dust collection. Of course, this is a rabbit hole in itself, and before I knew it I was looking at $1500+ cyclones, and crossing off anything without HEPA filtration, and then the prevailing opinion was even that wouldn't be sufficient. So I ended up not buying anything at all, and continuing on with cleaning up after the tools with the shop vac. Part of my issue is that I just don't have the room for a cyclone, and even a short 1.5hp one would be a real squeeze.

I started thinking this morning that this is ridiculous, and went over to Busy Bee to check out their boxing day sale. For those outside Canada, Busy Bee is a woodworking and tool store that carries a lot of the same machines as Grizzly but with different paint jobs. I saw a small 1 hp dust collector on sale for $325, the CX404. It would fit in my garage, it was well within budget (even if I upgrade or add a canister filter later) and it looked to be powerful enough for one tool at a time operation without issue. The footprint of it is around 17"x24", which for me is perfect. There isn't a directly comparable Grizzly model, but it's sort of in between a couple of their smaller 1 hp dust collectors. It is a 1 micron bag, but nothing Busy Bee sells has better filtration than that, even the canisters. At some point I may look at ordering an appropriately sized HEPA canister for it.

I got it home and opened up the box. It was pretty compactly packed in there. 

20171228_151006.thumb.jpg.7c54b2375a57905396d78cf77a59ba27.jpg

The only disappointment was I had thought that a short 4" hose was included. It looks like I'll be headed back either there or Lee Valley tomorrow so I can use it.

20171228_151044.thumb.jpg.320ee19293870288514579e7b69f6c66.jpg

I spread it out on the work bench and put it together. It was pretty easy, only took about 20 minutes.

20171228_151519.thumb.jpg.ef6252c3dcccb14c0e82921ae49fb99d.jpg

And here's the end result. The collector is not even 5' tall, but on paper it should have pretty decent specs for my needs. I turned it on, and I can tell that it's sucking air in, but that's about it without the hose.

20171228_160829.thumb.jpg.eadc7beb14bf1d9e4476e4ee2f2fcb23.jpg

Once I get it running with my tools, I'll post a bit more. I figured I'd start a thread on it because there doesn't tend to be much information on these smaller dust collectors. While something larger would be great, this will be a lot better than having no dust collector at all.

Smart choice, Brian. I would definitely prefer a small dust collector over no dust collector. 

Your going to be really happy with some dust collection. With out a cyclone I don't know that i'd do a hepa filter. Larger and the huge amount of small dust getting to the filter will clog it up quick. Are you planning on running a drum sander on that DC?

  • Author
24 minutes ago, Chestnut said:

Your going to be really happy with some dust collection. With out a cyclone I don't know that i'd do a hepa filter. Larger and the huge amount of small dust getting to the filter will clog it up quick. Are you planning on running a drum sander on that DC?

No, I'm planning on just using it with my table saw and planer, maybe with the drill press and lathe for general cleanup. No room for a drum sander in my space. My dust collection needs should be pretty basic.

  • Author

So I went and got a 10 foot flexible hose to go with it, along with a quick disconnect fitting. I turned it on, and it sucked, as expected. When I connected to my table saw it cleaned out the cabinet, with a little thumping on the side. The collector worked well, although I had a small leak at the point where the clamp is on the bottom bag. I'll have to adjust it and tighten it up before running it again. I'm reasonably happy, although I think I'll want to seal up my table saw a little better.

  • Author

I had another look last night and was able to improve the seal on the bottom bag, but it still wasn't perfect. It seemed like right under the clamp latch the bag was folded over a bit and letting a little through. Has anyone used something like wide weather stripping under the clamp? I was thinking about picking some up today, since I was able to find 1.25" wide and 1/8" thick closed cell foam tape when quickly looking it up. It's usable as is, but I'd like to solve the problem up front.

  • Author

I was able to significantly improve the seal to the bottom bag by applying closed cell weather stripping. I found this stuff at HD and it's 3/16" thick and 1 1/4" wide in a roll. It's pretty much perfect for the application. The bag was a little harder to put on, but the only leaks now are a couple of pinhole leaks in the plastic bag itself. If I was to do this over again, I'd apply it before assembling the unit.

20180106_132522.thumb.jpg.b78c0ee4cd6756920909c2b4543d30a9.jpg

I think it's good enough to try using it on the bookshelf project. I sealed up the table saw a bit more to try and direct more air to the throat plate. I'm assuming I want the remaining open area on the saw to equal the area of the 4" port, so I'll try to figure that out.

10 hours ago, SawDustB said:

I'm assuming I want the remaining open area on the saw to equal the area of the 4" port, so I'll try to figure that out.

Not necessarily. Choking it down a bit can potentially increase the air speed around the blade giving you better collection. Trick is to keep the flex hose to the DC short and makre sure the fittings on the hose seal well.

  • Author
7 hours ago, Chestnut said:

Not necessarily. Choking it down a bit can potentially increase the air speed around the blade giving you better collection. Trick is to keep the flex hose to the DC short and makre sure the fittings on the hose seal well.

All right, I'll have to experiment. I closed the gap at the table top, and I have some sheet magnet blocking the tilt adjustment slot. I can't see any other big holes except for the throat plate (which I want, obviously). I'm just looking at that area left open and it seems pretty small.

1515329089861473548225.thumb.jpg.82ead47d40f7d738084905e5366e1a05.jpg

I'm using a 10 foot flex hose as my only connection to my tools. My space is small enough I can leave the collector stationary for the table saw and planer and also use it at the work bench. All the connections are clamped using the bridging clamps, and I just have the one quick connect at the end of the hose.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.