Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Cut List?

Featured Replies

Wouldn't mind making this out of white oak or cedar, but would prefer to source it more locally than Oregon.

Is there a cut list available, other than having ~30 bf of wood? :-)

Wouldn't mind making this out of white oak or cedar, but would prefer to source it more locally than Oregon.

Is there a cut list available, other than having ~30 bf of wood? :-)

Dean,

You may also want to consider Cypress. Not sure of your local source prices but down here in Houston, cypress is pretty affordable and it is a rot resistant wood that is a good choice for outdoors. It also, depending on your view of things, has an advantage over red aromatic cedar in that it is more color consistent. It's not quite double the price of aromatic red cedar (for me locally its the difference between $75 and about $120 for one chair) Now Spanish Cedar is a different choice, but that tends to be on par cost wise with Mahogony (at least from what I have seen in the local Houston hardwood store price sheet). Mahogany or Spanish Cedar pushes the price between $250 and $300. Anyway I see Cypress as a nice compromise and like the idea of the color consistency. White Oak gives you that as well but Oak in general is a porous wood that even with grain filling and such in an outdoor environment I feel like it will pick up more grime and dirt and have places for mildew to begin growing.

Just my thoughts and thinking at this point - not sure which way I will go for sure, but I am definitely leaning towards Cypress.

Dean,

You may also want to consider Cypress. Not sure of your local source prices but down here in Houston, cypress is pretty affordable and it is a rot resistant wood that is a good choice for outdoors. It also, depending on your view of things, has an advantage over red aromatic cedar in that it is more color consistent. It's not quite double the price of aromatic red cedar (for me locally its the difference between $75 and about $120 for one chair) Now Spanish Cedar is a different choice, but that tends to be on par cost wise with Mahogony (at least from what I have seen in the local Houston hardwood store price sheet). Mahogany or Spanish Cedar pushes the price between $250 and $300. Anyway I see Cypress as a nice compromise and like the idea of the color consistency. White Oak gives you that as well but Oak in general is a porous wood that even with grain filling and such in an outdoor environment I feel like it will pick up more grime and dirt and have places for mildew to begin growing.

Just my thoughts and thinking at this point - not sure which way I will go for sure, but I am definitely leaning towards Cypress.

Good info, Jim. In Japan, Ofuro bathtubs are made of a Japanese variant of Cypress. Pretty rot resistant when you think it spends 1/3 of its day holding scalding hot water on just one side of the boards.

  • Author

Hey Dean. Have you gone to the Adirondack Chair page on the Guild site? The full plan and cut list are available for download.

Looks like a swing and a miss on my part; thanks!

  • Author

Dean,

You may also want to consider Cypress. Not sure of your local source prices but down here in Houston, cypress is pretty affordable and it is a rot resistant wood that is a good choice for outdoors. It also, depending on your view of things, has an advantage over red aromatic cedar in that it is more color consistent. It's not quite double the price of aromatic red cedar (for me locally its the difference between $75 and about $120 for one chair) Now Spanish Cedar is a different choice, but that tends to be on par cost wise with Mahogony (at least from what I have seen in the local Houston hardwood store price sheet). Mahogany or Spanish Cedar pushes the price between $250 and $300. Anyway I see Cypress as a nice compromise and like the idea of the color consistency. White Oak gives you that as well but Oak in general is a porous wood that even with grain filling and such in an outdoor environment I feel like it will pick up more grime and dirt and have places for mildew to begin growing.

Just my thoughts and thinking at this point - not sure which way I will go for sure, but I am definitely leaning towards Cypress.

Pittsburgh, PA; no Cypress here, but great big stacks of walnut, oak, cherry, maple, and whatnot. :-)

  • 2 weeks later...

Hi guys, total newbie here. I made a trip to local mom and pop woodshop, plenty of choices, they too recommend "Cypress". I think i'll go with that. I have a basic question regarding BF(board foot). I noticed Marc's cutlist totals 20ish BF. The Bell Forest kit says it contains 30 BF. To me that's a huge difference especially given the cost of your choice material.

My question is: Why the variance in totals?

Thank you in advance

I was going to explain but I figured I would let Bell speak for themselves:

"For projects like this I always try to include more than enough material for the project. I know that wood is not perfect, and neither are woodworkers. We want to make sure they get enough wood the first time around. Nobody likes calling to say they messed up a piece or ran short and need one board mailed to them. The 30 bf is probably a little excessive. When putting together one of these kits we begin with 30 bf. After the planing, ripping, and chopping, most of the kits have been shipping at about 25 board feet. I will have someone update the site to reflect that."

"For the rough packages we are sending 32 bf of material. Again, we want to make sure you have enough wood for the chair. I hope they don’t mind having a little bit left over for another project!"

Eric Poirier

Bell Forest Products

Just to pile on to Bell Forest's reply, the numbers in the cutlist are calculated assuming a 1/4" bubble around the finished parts. I know, since I did the calculations. Trees don't grow exactly the right width or length, so you have to plan for some loss when cutting the parts out of the lumber.

So the finished parts are 20 BF, but you will certainly need more raw lumber to create these parts.

Ok, makes total sense know. I was racking my brain and changing batteries in my calculator....haha. Thanks again guys!

I'm thinking of making mine with walnut, since I have so much of it. Maybe using cherry for the plugs. Then again, I might make mine from cherry, again since I have so much of it, and making the plugs from walnut. I was surprised to read that both species are listed as rot resistant.

Hi Keggers...I was surprised to find Walnut and Cherry on that list too. I was concerned with getting the right species of Walnut and Cherry. They had mentioned in the PDF that Marc shared (I think it was that document) that you needed to use Black Walnut and Black Cherry. Is the standard Cherry that everyone typically works with a Black Cherry? I know there are different types of walnut, and like you I have quite a bit of that stock laying around, but am not sure it's Black Walnut.

I think the contrasting woods are going to look awesome for this build. I was thinking of doing Walnut or Wenge plugs on my White Oak chair. I don't mind using ebony though...but for some reason I'm having a hard time finding a decent size piece without paying an arm and a leg for it.

See ya around the Guild Build!!!

Hi Keggers...I was surprised to find Walnut and Cherry on that list too. I was concerned with getting the right species of Walnut and Cherry. They had mentioned in the PDF that Marc shared (I think it was that document) that you needed to use Black Walnut and Black Cherry. Is the standard Cherry that everyone typically works with a Black Cherry? I know there are different types of walnut, and like you I have quite a bit of that stock laying around, but am not sure it's Black Walnut.

I think the contrasting woods are going to look awesome for this build. I was thinking of doing Walnut or Wenge plugs on my White Oak chair. I don't mind using ebony though...but for some reason I'm having a hard time finding a decent size piece without paying an arm and a leg for it.

See ya around the Guild Build!!!

I'm not sure about the black cherry, but I know mine is Missouri black walnut. I'm building my chairs mostly, (I'm building two) from quarter sawn walnut. All except for the wide back slats and probably the arms. I'll try to keep as much straight grain in the back slats and arms as possible. I'm really looking forward to this build. It's the first one I've been able to participate in.

  • 3 weeks later...

Recently I purchased the lumber for this Adirondack Chair guild build and I went with White Oak (less expensive and fairly rot/weather resistant). I recently made a Father's Day gift for my Dad using some of the "extra" White Oak from the Adirondack build stock. I'm realizing after this project that I'm not a real big fan of the grain patterns and color of the White Oak. I'm not sure how I'd like it as a chair option either. To me (and this is just my own opinion) the wood looks dirty and quite muddled with the open grain (and not in a good way). Now, this could just be the stock I purchased, or maybe this is a common characteristic for most White Oak. In a way I'm glad I did this first project so I was able to see what the White Oak really looked like finished...but I'm not so sure I'll be using it for the Adirondack project...we'll see. I'm going on vacation next week and it'll give me some time to come up with some other options.

I hear you, SSG. I bought some cypress for my chair, and I don't love how it looks either. I'll finish the chair before I make my final decision, and maybe switch to a different wood if I build another chair in the future. I love the look of teak or other tropical hrdwoods, but $$$$! The cypress was reasonable and hopefuly with weather nicely.

Sorry to hear that Aaron, I was thinking of going with Cypress. :rolleyes:

Don't let me talk you out of using cypress. I think some of the stock I got looks great. The 8/4 was nice tight grain, almost quartersawn. It's just that the 4/4 stuff I bought is flatsawn, and has heavy and obvious cathedral figure. Just not my thing. I just wasn't careful enough in my stock selection, nothing against sypress in general.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.