Recommended Posts

Posted

I need to bust out my router table for an upcoming project, so I have to break down and get a fence (the biggest missing component). I'm currently thinking either the Rockler for its cost and simplicity or the Kreg for its sheer awesomeness. The Woodpecker is also a dark horse in the race.

Anyone have one of these? what do you think of it? Any advice?

Posted

I need to bust out my router table for an upcoming project, so I have to break down and get a fence (the biggest missing component). I'm currently thinking either the Rockler for its cost and simplicity or the Kreg for its sheer awesomeness. The Woodpecker is also a dark horse in the race.

Anyone have one of these? what do you think of it? Any advice?

I have the rockler kit (table and fence) on my table saw, the fence is nothing special, piece of angle iron and two mdf fences with a formica face, you'll probably want to also get the dust adapter for the back of the fence bringing the cost to about 95 bucks not a "bad" price compared to the other two you are looking at purchasing, although the other two are probably better quality, I can't speak to them though. on a side note I'm actually planing on building an attachment for my table saw fence since its already there.

20101121%252520001.jpg

Posted

Hi Diami,

is you router table stand alone, or is it part of your table saw? I found this design and built it with a few modifications. I made the fences out of melamine, and make them moveable and adjustable using recessed t nuts. IMHO it is every bit as good as the fences you mentioned, and better in that i can control the fence WAY better than i could when it was a stand alone unit. Just my 2 cents..... BTW, the fences can be made of MDF as well, and set up to provide a zero clearance cutting surface. The hole in the end is 2.25". Dust collection works great! Find the article and design here:

http://www.finewoodw...e.aspx?id=33274

If you cannot see the article, let me know and I'll copy and paste it for you. Hope this is of help!

Gerry

011211014_01-router-table_lg.jpg

Posted

I own the rockler fence but I would not buy it today if I were in the market for a fence. It does the job but the mdf front leaves a lot to be desired. Essentially it is just too delicate to ever feel like I can just use it without having to be worried I will damage it. The first day I had it I put a clamp on the front and caused a crack in the mdf part of the fence.

I can't tell from the picture whether the kreg fence is all metal, but certainly the woodpecker fence is all metal. I would stick with one of those fences over the rockler. Or you could just make your own rockler style fence. 18 dollars in your local hardware store will buy you the right size piece of angle iron. A drill press and a jig saw with a metal cutting blade will allow you make all the appropriate holes. After that you can use mdf for the fence front like the rockler, or better yet some 3/4" hardwood plywood.

Does your router table have t-tracks installed on it for the fence to attach? If it doesn't then certainly you will need to factor those into the cost of your fence (only about 20 dollars) and certainly the kreg fence gains a leg up here since it does not require them to function.

Posted

I own the rockler fence but I would not buy it today if I were in the market for a fence. It does the job but the mdf front leaves a lot to be desired. Essentially it is just too delicate to ever feel like I can just use it without having to be worried I will damage it. The first day I had it I put a clamp on the front and caused a crack in the mdf part of the fence.

I can't tell from the picture whether the kreg fence is all metal, but certainly the woodpecker fence is all metal. I would stick with one of those fences over the rockler. Or you could just make your own rockler style fence. 18 dollars in your local hardware store will buy you the right size piece of angle iron. A drill press and a jig saw with a metal cutting blade will allow you make all the appropriate holes. After that you can use mdf for the fence front like the rockler, or better yet some 3/4" hardwood plywood.

Does your router table have t-tracks installed on it for the fence to attach? If it doesn't then certainly you will need to factor those into the cost of your fence (only about 20 dollars) and certainly the kreg fence gains a leg up here since it does not require them to function.

Applewood,

Thanks for the feedback. I think I'm putting the fence on hold for a little as I'm now not sure how I'll do this project. That said, I'll be keeping my eye on the fences. Assuming I haven't gotten one by then, I'll certainly be checking them all out at WIA.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 43 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined