Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Template routing with a plunge router

Featured Replies

I must be missing something obvious.  This should be a simple, straightforward operation and I just can't figure it out!

I want to route a 1/2" recess using a template.  My template is 1/2" thick.

So, I figure I'll use a plunge router, set the depth stop at 1/2", and make multiple passes until I hit my stop.  The first passes index off the template, and deeper passes index off the earlier passes.  That's the whole point of a plunge router, right?

Here's the Whiteside bit I'm using

Templatebit.thumb.jpg.930380d444dcce3722b2e75f3989b8e2.jpg

Here's the bit in my router.  I dropped it in all the way and then lifted it up a hair, because someone on YouTube told me to.

Plungerouter3.thumb.jpg.1be5fdbb3b5c5c719d44debe860f124c.jpg

Here's the whole thing in the plunge base, plunged all the way down.

Plungerouter4.thumb.jpg.6b61f0595b3af80c8562e3d4c0196b17.jpg

Notice that the rubber sleeves are scrunched all the way down - it's not going any further.

Plungerouter5.thumb.jpg.b4c088e18382bcc4e9ff05a6a139226c.jpg

That only gives me about 1/2" of total depth.  I need twice that.  

I could pull the bit 1/2" out of the router, but that doesn't seem safe.  I've already had problems with router bits slipping (cursed be the name of Triton) so I don't want to cut corners.

The only other thing I can think of is to use a thicker template and a longer router bit.  But I don't want more cutting, I just want a longer shaft.

Am I missing something?

 

  • Popular Post

No you're not missing anything. That's a pretty small bit and that's it's max depth. Plunge routers aren't really designed to plunge deep. It's the length of the bit that will ultimately determine your depth. The plunge action just allows you to begin your cut in the middle of a work piece.

I agree with Doug on this. It appears you could pull the bit out some but I don't think you can pull it out enough to get what you are looking for and as you mentioned if you are having bit retention issues not the best idea. 

  • Popular Post

Take the collet nut out of the machine and insert the bit shank through the collet until the end is flush in back. You can pull the bit out that far and still have full contact with the collet. If that isn't enough, you might get a smidge more depth by swapping the thick baseplate for a thin piece of hardboard / masonite, or even sheet metal. It just provides a smooth surface to glide over edges in this case. I was going to suggest the motor might go farther into the base, but it looks bottomed out 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.