Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

A few notes from my bench build

Featured Replies

Two summers ago I built a bench with the Benchcrafted tail vise and leg vise. I used a combination of the Benchcrafted plans, which are excellent, and the Christopher Schwartz’s Workbench book, which was indispensable. The bench was my first major project. If I could build one, anyone can. For me, the bench build was less technical and an easier build than the Shaker Table. It was absolutely easier than the Adirondack chair build. Mark's videos and advice will no doubt make this project doable for everyone.

Random thoughts from the build:

  • It took a few months.
    • I bought 20 2x6x16 pine boards. The nice folks at the lumber yard were kind enough to cross-cut each of the 20 boards at 8 feet. They also ripped a few of the now 8 footers at 5 inches (for my legs) a few at 3 inches (for my stretchers) and the rest at 4 inches (for the bench top). They also loaded it all in my truck.
      post-513-0-29771100-1321988991_thumb.jpg
      • As far as using pine goes, it was cheap and it's just a workbench. Dings caused by my carelessness are easy to repair with epoxy.
        • A few have wondered whether the bench can be built without having another bench available. I got by pretty well with 2 plastic saw horses. At one point, the bench top rested on those for over a week. I was certainly careful walking around it, but never had any close calls.
          post-513-0-58383400-1321989014_thumb.jpg
          • I did not use a jointer, but did use a planer quite a bit. My router and a high quality ½ inch up-spiral bit got a ton of use, particularly in hogging out material for the tail vise and the mortises.
            • I used an old brace and bit to bore a few holes in the top for the holdfasts. I love those things.

              • I glued up the top in sections of 3 boards a time, and then glued those sections together 2 at a time. I only needed 24” clamps once, and that was for the final bench top glue up.

              [*]I went with a maple breadboard end-cap because the thought of dovetailing that thing was too intimidating. My deadman and the chop are oak.

              [*]I elected not to use hardware to join the top and legs and stretchers, relying instead on epoxy, large mortises and tenons, and drawboring. http://www.wkfinetoo...drawBoring1.asp

              [*]I used the finishing recipe from the Workbench book of 1/3 varnish, 1/3 thinner, and 1/3 blo. No complaints and easy to reapply. Mark has talked about this here: http://thewoodwhispe...-varnish-blend/

              [*]I love the Benchcrafted vises. Definitely worth the money and the time it took to install them.

              [*]I went with square dog holes instead of round, mainly because of this post http://benchcrafted....bench-dogs.html. I would absolutely do the same again.

              Any questions?

              Mike

  • Author

Here are a few pictures. After Thanksgiving, I'll see if I can find any pictures taken during the build.

The bench top ended up being around 20 inches wide and just over 8 feet long.

post-513-0-98173300-1322065133_thumb.jpg

post-513-0-86630100-1322065142_thumb.jpg

post-513-0-15021800-1322065122_thumb.jpg

  • 1 month later...

Mike - this looks like a fantastic build. Thank you for posting it. If you are so inclined, you should convince Marc into doing a bench interview with you as part of the guild build. It would be interesting to hear more detail about the whys, wheres and hows regarding this and how you've been using it since it was built. The cheapskate in me kind of likes the "big box store wide pine board" approach that you mentioned and Chris Schwarz recommends in his book. After all, you make bench to be beaten on, right? My wallet (and my wife) would rather have me beat on $200 worth of pine than $1000 of hard maple. And while we'd like to think that this will be the last one we ever make, chances are that, at some point in the future, most of us "first bench" builders are going to either modify what we have or rebuild another "last bench ever". Thanks again.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.