croessler Posted February 1, 2012 Report Posted February 1, 2012 So, a quick question for all you Neanderthal types... I have several old Stanley 720's and a couple of old sash chisels that I haven't identified yet. They all need new handles as these where my dad's and he was from the "if it doesn't fit get a bigger hammer" club; if you get my drift. I can turn the new handles easily enough however I don't know how to fit them to the sockets properly not to mention how do you get them to stay? Any suggestions would be helpful. Thanks, Chris Quote
Mister Pants Posted February 1, 2012 Report Posted February 1, 2012 Supposedly they can be friction fit only for the sockets. However I'm not a great turner so I got them close, friction fit and used epoxy to secure the handle. I'm sure that's not the best way though, but it has worked for me. Quote
JayWC Posted February 1, 2012 Report Posted February 1, 2012 Chris Schwarz posted a short video that talked about using hair spray to afix the handle into the socket. http://www.popularwoodworking.com/woodworking-blogs/chris-schwarz-blog/new-stanley-chisels-a-fix-for-loose-sockets Quote
TimV Posted February 1, 2012 Report Posted February 1, 2012 I just finished turning a set for some old chisels I restored. I turned them first using a 3-jaw chuck and tailstock. Then I removed the tailstock and tapered the the socket end. It was a trial and error process for each one since they were all different sockets. When you slide the socket over the tapered tennon, it will leave marks where it contacts. Remove a little material at the mark and try again. Repeat as necessary. If the fit is good, you won't need hairspray, but hairspray works. You really don't want to use epoxy otherwise you'll have a heck of a time getting the handle out if in the future you want to. One important note: make sure you use completely dry wood. Otherwise, the handles will shrink ever so slightly and you'll find yourself adding a wrap of blue tape around the taper....ask me how I know.... Quote
wilburpan Posted February 1, 2012 Report Posted February 1, 2012 Use your lathe to turn your handle, and turn the end of the handle that sticks into the socket as best as you can to match the socket. Then take a pencil and scribble all over the inside of the socket. Push the handle into the socket and take it out. You'll see the graphite from the pencil where the socket rubs up against the wood of the handle. Pare down those areas, and retest the fit. You should see more dark areas as the fit will be a bit closer. Pare away those areas, and keep repeating until you get a good tight fit. Edit: okay, Tim types faster than me. To take care of the shrinking handle problem, make the handle a little thicker than the socket. Then you can trim down the end of taper to give you room to push the handle in further, and there will be some wood at the top that will help fill in the socket. Quote
JayWC Posted February 2, 2012 Report Posted February 2, 2012 One important note: make sure you use completely dry wood. Otherwise, the handles will shrink ever so slightly and you'll find yourself adding a wrap of blue tape around the taper....ask me how I know.... I feel for ya, but I give you a lot of credit for admitting the mistake in order to help others. Quote
SamV Posted February 17, 2012 Report Posted February 17, 2012 Excellent points Wilbur. I've turned a few socket handles and they really need a small gap left between the steel and the shoulder to allow for movement and shrinkage. This allows for annother good smack if it ever comes loose. Speaking of chisel handles: http://www.pbs.org/woodwrightsshop/video/3100/3112.html This is something I really want to try. Quote
HoboMonk Posted February 17, 2012 Report Posted February 17, 2012 I agree with Wilbur on using soft pencil lead to create dry fit witness marks. For socket chisels, a couple of drops of shellac can be used to affix the handle in the socket. If you ever need to remove the handle, shellac softens at a temperature slightly below the boiling point of water. Besides, shellac is more manly woodworkerly than hairspray. Shellac also makes a good lock tight liquid for machine nuts and bolts. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.