tim0625 Posted December 28, 2012 Report Posted December 28, 2012 Hi there everyone. Life has been hectic but I have slowed down a little for Christmas etc. I am in the process of setting up my tablesaw. I have built an elaborate outfeed table but have yet to fit the mitre slots. I have them but other things get in the way. I am going to set a router insert into the table on the right hand side of the rip fence and create a dust collection/ adjustable fence out of ply when I can afford it. Dave....Nice out feed table. The pattern goes well with the saw. I've never heard of this but seeing your miter slots that still have to be cut gave me an idea. Would there be a friction advantage if you cut your slots - say - 1/32 deeper and 1/16 wider and line the slot with laminate? It shouldn't be too hard to do and would give a friction advantage as well as further sealing your out feed table from moisture. Quote
Beechwood Chip Posted December 28, 2012 Report Posted December 28, 2012 have yet to fit the miter slots. I have them but other things get in the way. Are you going to try to install T-track to line up with the existing miter slots? I'd recommend just making a slightly over-sized dado. I'd be concerned that any slight shifting of the outfeed table would throw the T-track out of alignment. Quote
davestanton Posted December 28, 2012 Author Report Posted December 28, 2012 I am using t track. The saw and table are bolted together using the holes that used to take the rear angle bar that supported the rip fence as well as the last hole to the right on the front rail. My tools don't have a lot of biff happening to them so I think it should remain accurate. Quote
davestanton Posted December 28, 2012 Author Report Posted December 28, 2012 Tim. I will seal the slots prior to fitting the t tracks. Quote
davestanton Posted December 29, 2012 Author Report Posted December 29, 2012 Fitted the tracks today and completed fastening the outfeed table to the saw. Rock solid. Quote
tim0625 Posted December 29, 2012 Report Posted December 29, 2012 Fitted the tracks today and completed fastening the outfeed table to the saw. Rock solid. Awesome Dave Quote
Dave F Posted December 29, 2012 Report Posted December 29, 2012 Very, very nice! Somebody is gonna be havin' some fun making piles of sawdust. Looks like you have a fantastic set-up. Well done !! Quote
davestanton Posted December 30, 2012 Author Report Posted December 30, 2012 As my mitre guide has one of those discs near the base of the bar that stops the guide lifting out of the track, I used the same style of T slotted mitre guide track. This should go well with my mitre guide and also with any sleds that I make or buy in the future. The next trick is to install the router insert and also the kreg mitre slot/ mini t track combo. There will be no sawdust generated in my shop for a long time to come other than generated by my making things for the shop. To me, the shop setup is a very enjoyable process and I know that if something doesn't work as I had planned it to, then I become irritated. Just my personality, I am a bit of a control freak. The shop is a place for me to come to sit and relax, make something if I want to, unhindered. Maybe watch some tv, maybe listen to some music, maybe fix a pushbike for one of my grandchildren or simply inflate a football. That is the great thing about it....no pressure. It should always be clean and clear, ready for me to do as I please. I have drifted off course a bit there, but I guess that some of you would understand where I am coming from Quote
TRBaker Posted December 30, 2012 Report Posted December 30, 2012 I understand perfectly, Dave. However you are mistaken on one point. If you are going to inflate a football, there needs to be pressure. Quote
davestanton Posted December 30, 2012 Author Report Posted December 30, 2012 Indeed you do, lol. But, I have a compressor to do that for me with the hose mounted on the ceiling. Such a nice place to hang out. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.