Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Wipe on finish for kitchen cabinets?

Featured Replies

Hi all, I hope I am not asking too redundant of a question but could not find anything in the searches I have done.

I am building (or going to build -- still planning) a new kitchen. Fo the boxes I will use pre-finished maple ply -- no problem. The face frames, doors, drawers, panels will be cherry -- likely unstained but I may apply a gel stain. My question is what would be a good wipe on finish that would be durable enough. I don't currently spray, and considered purhasing a Earlex 5500 HVLP but I believe there is a learning curve on spray techniques and don't want to learn on my kitchen project. I was considering one of the General Finishes wipe on products -- Urethane Wipe On Topcoat, Arm-R-Seal Oil & Urethane Topcoat, EF High Performance Polyurethane Topcoat, or even Marc's oil and varnish recipie. Any recommendations. I may even consider a brush on finish like EP PolyArcrylic Blend Top Coat.

Anyone wipe on a finish on kitchen cabinets and have a strong recommendation? Should I be going the spray route? Time not an issue so I would not go spray for the speed of it.

A couple of thoughts from the cheap seats.....

If time is not a consideration, wipe-on would be my preferred approach. The quality control you achieve with this option is unsurpassed, and I make this observation as the proud owner of a Fuji. Obviously, you need to put on more coats than spray because of the finish depth.

Another "plug" for hand finishes is the inevitable future repair you will undertake as wear and tear sets in. When you start getting into harder acrylic-like finishes, it is more difficult/impossible to do spot repair that blends.

I don't have a brand recommendation beyond Marc's approach. Mixing your own (and you might need to tweak a bit) is much more cost effective and gives you some latitude on blends. Since you are going G&G, do consider a refresh on Darrell's finishing techniques to inform your efforts.

Hope this helps. I am by no means a finish expert, but I do have an autographed copy of Marc's book! :)

I prefer a wipe-on finish myself, and refinished our kitchen cabinets with Minwax Satin Wipe-On Poly over ten years ago. (probably more like 15). Anyway, they still look as good as the day they were done. If memory serves, I put on 5 or 6 coats. I'm sure there are more durable finishes out there, (a lot of people like GF Arm-R-Seal) but the Minwax stuff is so forgiving and durable enough for me based on the results I've always had with it.

  • Author

Thanks for the feedback. I'll stick with wipe on. I prefer an oil + varnish mix but was concerned about durability in a kitchen environment. I know polyurethane is very durable but just not a fan of that plastic look you can get with that. Maybe I should just buy a can of each of the GF products and do test pieces and see which I like best and which is more durable.

PS. I'm itching to get started but been waiting for my wife to make up her mind on appliances and she wants to hire a kitchen designer to help with the layout. I've been waiting since....let's see.....January...meanwhile, my shop stands idle except for doing mockups.

If you would like, why not post a floorplan of your kitchen and see what the forum might turn up for you? (hint, hint). If you include a list of the types of appliances you might be looking for, I'll bet there might be a few thoughts coming back your way. This could be a great opportunity for a Sketchup drill!!

  • Author

She has already met with the designer so we'll see what comes from that. Once I have that I will post. Not a sketchup but likely a sketched drawing that I can scan and post (have to be careful about copyright issues so may have to get permission). The designer has seen my G&G face frame mockups so maybe she will incorporate that into the drawings.

I would not use a wipe on on a kitchen cabinet. You dont get good wet coats like spraying. If you want a sprayer this would be the time. Vinyl sealer with a precat lacquer top coat would be a longer lasting finish. I think it would be very easy for you to learn to spray lacquer and it is so forgiving anyone can spray it. Even better would be a conversion varnish and with the way companies like Sherwin Williams catalyze it for you its almost fool proof. The only problem with having SW catalyze for you is pot life, so you have to run home and spray asap.

Don

  • 3 weeks later...

So what did your designer decided about your kitchen project? Would like to know about it. I will also suggest spraying is the best option but it's your decision finally.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.