Grain Guy Posted July 13, 2012 Report Posted July 13, 2012 Just got my first router plane,a stanley #71. Any good tips or jigs for honing these blades? And, there is an adjustment on a plate in the front of the base. How is this used? Later Quote
RenaissanceWW Posted July 13, 2012 Report Posted July 13, 2012 Congrats this is probably one of the most valuable joinery planes out there. It can be used for many different tasks. Maybe you stretch the boundaries a bit to do it that way but nonetheless a great plane to start with for joinery. First the adjustment plate on the front is to close off the front of the mouth so the sole can reference on a narrow surface like the edge of a stile where you are refining a groove. It can also be set to specific depths when you have to control depth or have a stepped work piece. Sharpening is a piece of cake. Focus on the flat of the iron and sharpening that until you get a burr on the bevel side. Then with your stone elevated off the bench, you can turn the bevel down with the post running off the edge of the stone to remove the burr. Now off to work! Quote
croessler Posted July 13, 2012 Report Posted July 13, 2012 Always wondered... How do you sharpen the Router plane cutters? Quote
Grain Guy Posted July 13, 2012 Author Report Posted July 13, 2012 Thanks man. The blade that came with it had been rode hard and put up wet. It's been over worked and won't hold a edge very long. I ordered replacement blades from veritas. Quote
Grain Guy Posted July 13, 2012 Author Report Posted July 13, 2012 What would a spear point blade be good for? Quote
RenaissanceWW Posted July 13, 2012 Report Posted July 13, 2012 I essentially skews the cutting action and will leave a cleaner cut in tough stock. It is also nice to skew the whole plane and use the point to get into tight spots like the bottom of a sliding dovetail. Quote
nateswoodworks Posted July 15, 2012 Report Posted July 15, 2012 I agree that for jointery this plane is the plane. I only use 2 cutters, the 1/4" and the spearpoint. The spearpoint leaves a much smoother cut because of it's snowplow like design, definitely worth every penny. The only downside is that it's 1/2", great for a lot and too wide for a lot but luckily it only takes a minute to switch back and forth. As for sharpening both are pretty straight forward but for the spearpoint either making a holder or buying the one Veritas sells will make it easier since the little thing is harder to hold (it's easier to sharpen with the cutter removed from the stem) For my 1/4" just like Shannon said, I hone the bottom and then the bevel. I planed a scrap that I set my stone on (I use oil stones so the dimension never really changes) that puts the bevel perfectly flat on the stone while the stem rides along the benchtop, just makes it more stable. Have fun, this plane will change the way you do woodworking! Quote
CessnaPilotBarry Posted July 15, 2012 Report Posted July 15, 2012 Spear points even work great in plywood, if a tablesawn dado needs a touch up. Some folks also use router planes, instead of shoulder planes, to fit tenons. Using an offcut to support the side of the plane that can't rest on the part, working from the edge-in, across the grain, the router plane can ensure a perfectly flat tenon cheek. The router will stop cutting when the preset amount of wood is removed. Quote
Tom Conover Posted July 16, 2012 Report Posted July 16, 2012 Thanks for smae great info. I had read about the router plane in Schwarz' Anachist book and he also felt that this was a must have in your stable of joinery tools. Quote
nateswoodworks Posted July 17, 2012 Report Posted July 17, 2012 Some folks also use router planes, instead of shoulder planes, to fit tenons. Using an offcut to support the side of the plane that can't rest on the part, working from the edge-in, across the grain, the router plane can ensure a perfectly flat tenon cheek. The router will stop cutting when the preset amount of wood is removed. Thats what I do. I have a #92 but honestly it collects more dust than shavings because the router plane is much more accurate. Quote
CessnaPilotBarry Posted July 19, 2012 Report Posted July 19, 2012 Thats what I do. I have a #92 but honestly it collects more dust than shavings because the router plane is much more accurate. Can't beat the depth stop! Along with tenon face adjustment, I almost always use router planes to mortise hinges, even entry doors in trim carpentry. It's fast, foolproof, quiet, safer, and easier to clean up after. And this comes from a guy who owns 11 electric routers! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.