Recommended Posts

Posted

Marc-- I own a Powermatic Jointer (1610086K Model 60HH 8-Inch 2 HP) and I find that is tends to get clogged up with saw dust. Have you had any issues? My DC is one of the small Rockler 3/4 HP units but it seems to be sucking whatever gets to the hose.

I take pretty small cuts, but it still seems to get clogged near the top. Thoughts?

Posted

I know this is in the "ask Marc" section, but I had a similar problem with my Delta 6" jointer. Make sure your run of hose is short (especially if using flex hose - I use about 5 feet of 4" pipe). The problem with mine clogging was that I had a Y adaptor (5" split into two 4" ) on the DC intake. The dust would clog in the Y (usually starting with the long, thin shavings). I removed the Y, and there was a thin piece of plastic running accross the diameter of the intake (must have been in the manufacturing process). The chips where getting caught on this thin section of plastic, so I cut it out. It was about 1/8" thick and 5" long. Since I have removed it, no more clogs. Hope this helps.

*Marc - feel free to delete this if I should not have respoded in the "Ask Marc" board.

Posted

thanks pug. This is up in the machine itself, before it gets to the hose.

I do use a stretch of 4" flex hose, but that doesn't seem to be the issue. It works fine with the volume of my dewalt lunchbox planer.

Posted

First off, everyone is welcome to answer questions in this section. I can't read every post on the forum so this is a good way for me to quickly spot action items.

That said, yes, I have experienced this. It really comes down to two things: not enough suction and bad dust chute design. Obviously one has to compensate for the other. So as mentioned above, keep your run as short as possible to make sure you get as much air flow as possible. Also, take a close look at the area where the jointer sits on the stand. You likely have large air gaps all around the perimeter. I actually used some tape to cover the gaps in hopes that it would help direct the air flow up into the cutter head. This does help. So if you have a little more suction, either by improving the existing setup or getting a more powerful collector, and you plug up some of the holes, you should see at least some improvement.

I can tell you that in my old setup, before I moved out of the old shop, the dust was never a problem. When I came back to the old shop and tried a new ductwork configuration, I made some bad choices that resulted in the jointer being at the end of the line. There just wasn't enough air movement to do the job. End result was a frequently-clogged jointer.

Hope that helps. Moving this post to the power tool forum.

Posted

Thanks Marc, and Pug & Chip. I am glad to hear it's not just me. Sealing those gaps makes perfect sense. Perhaps I'll try some foam.

I've got a ton to do at the moment, but I'll let you know how I make out once I get to it. Thanks.

Posted

One other thing to add here. Clogging may also be caused by the type of wood being jointed. Something like maple will clog my 12" jointer and 15" planer pretty easily if I do a lot at one time. This is with an Oneida cyclone.

  • 2 weeks later...
Posted

Ok, So I took Marc's advise and went in and cleaned out the machine....

But check this out: Seems a mouse had taken up residency in the jointer, adding cotton bedding to the sawdust.

I hate mice.

post-789-0-08872500-1344218179_thumb.jpe

Posted

Ok, So I took Marc's advise and went in and cleaned out the machine....

But check this out: Seems a mouse had taken up residency in the jointer, adding cotton bedding to the sawdust.

I hate mice.

I was going on a road trip the other day, and decided to do some small checks of the car before I went. I topped up the fluids, and decided to blow out the engine filter with compressed air. I popped of the cap, and took out the filter. There were 4 baby mice in there, and the filter was shredded. First stop on the road trip, Canadian Tire for a new engine filter!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 50 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined