Ben@FineWoodworking Posted August 14, 2012 Report Posted August 14, 2012 I bought my table saw almost a year ago. I vowed that I was going to only use the stock blade for a day or so. Well... I never upgraded. The crappy stock blade is now a crappy stock dull blade. I'm more than a little confused over what to get. I am looking for a general purpose blade... probably 40 tooth. I'd like to match the kerf to my riving knife as best I can. On my knife it says: Thickness: 0.086" Blade Dia.; 10" Blade Body T.: 0.063~0.079" Blade Kerf W.: 0.094~0.118" So the thin kerf WWII is .125" thick... would that be to large for my riving knife? Thanks, Ben Quote
Ben@FineWoodworking Posted August 14, 2012 Author Report Posted August 14, 2012 I may have answered my own question... http://www.woodcraft.com/product/2000840/37763/forrest-ww10407100-woodworker-ii-saw-blade--10x-40t-100-kerf-x-58-bore-atb.aspx Concure? Quote
Guest Posted August 14, 2012 Report Posted August 14, 2012 I have had the Forest WW II thin kerf with stabilizer on my saw for over 15 years. Best blade I have ever used. Quote
Ben@FineWoodworking Posted August 15, 2012 Author Report Posted August 15, 2012 I've got a Grizzly 0715P. 2 horse. I'd go for a full size kerf but wouldn't that make my riving knife less effective? Quote
STL Woodguy Posted August 15, 2012 Report Posted August 15, 2012 I'd go for a full size kerf but wouldn't that make my riving knife less effective? I guess that depends on *how* much thinner the riving knife is. On paper, I would think it's still do it's job by keeping the wood from snagging the back or both pieces closing back up, better than nothing. Too thin and I might be able to imagine it still being able to snag the wood. I would still feel better matching riving kerf to blade kerf. On the other hand, the reverse scenario is no good period...when I first got my saw I had goofed by buying a thin kerf blade and forgetting I had a full kerf riving knife, so naturally that stopped the wood in it's tracks as soon as it reached the knife. I could of had the knife grinded down a bit, but I chose to go with a full kerf blade instead and have had that ever since. As mentioned, 2HP-ish saws should have no problem with them at all. Quote
CessnaPilotBarry Posted August 15, 2012 Report Posted August 15, 2012 I've got a Grizzly 0715P. 2 horse. I'd go for a full size kerf but wouldn't that make my riving knife less effective? To illustrate... .125 (WWII full kerf) - .086 (Your riving knive = .039" difference If the knife is centered, the teeth would have .0195" of purchase into the stock on each side. If the knife is not centered, you'd have a max of slightly over 1/32" of tooth into the wood. That's not a lot of purchase into the wood to give it traction to do much, unless you flat out let go of a small part, and not enough room to let a part seriously rotate into the rising teeth. I think you'll be fine! If you want a tick more pressure from the knife against the rip fence, you could add a thin strip of tape, think clear packing, not masking, to the side of the knife base where it clamps in the mount, to offset it towards the fence. Quote
knotscott Posted August 16, 2012 Report Posted August 16, 2012 Your riving knife should be fine with any blade that is at least as wide as the knife (a little wider is better), and the saw and knife are well aligned. Thin kerf is typically ~ 3/32" (0.090 to 0.100"), full kerf is ~ 1/8" (0.118" to 0.145"). Full kerf gives you more wiggle room, but is harder for the saw to spin in thicker materials, though your 2hp should do pretty well. Have you considered going with the full kerf 30T WWII? It'll give glue ready edges, will have a fairly easy time of thicker rips, and will even give acceptable crosscuts in most situations. As good as the Forrest WWII is, any general purpose blade is a compromise by design that won't do an outstanding job of any single task, but will do alot of them well. Something like this American made Delta Industrial 40T will give the 40T WWII a run for the money at < $30 shipped (closeout price). Similar story on this German made Onsrud 50T combo blade. Both will leave glue ready edges and will do a very good job at many tasks. The Delta 35-7657 has a kerf of 0.118", and would allow budget for another blade or two like a dedicated ripper or 80T ply/crosscut blade (like this 80T Oldham Pro blade for $30 shipped...also a closeout on a well made blade, or this 24T Oshlun ripper for < $25 shipped). You could get all three high quality blades for the price of a WWII...the ripper will be more efficient in thicker materials than the WWII, and the 80T will cut cleaner in ply/sheetgoods and fine crosscuts. Quote
knotscott Posted August 25, 2012 Report Posted August 25, 2012 Ben - Have you made any decisions yet? Quote
Ben@FineWoodworking Posted August 26, 2012 Author Report Posted August 26, 2012 Sorry. Lost track of this tread. Due to budget at the time I couldn't drop a lot on a blade and needed a sharp blade right then. I used a hd gift card and got a Freud that is serviceable for now. I'm glad to know that I don't need to worry about kerf size as much as I was. I'll look into those other options and report back when I finally pony up for a blade. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.