Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

spray system question

Featured Replies

I currently spray with the earles 5500...I bought it a while ago and have been happy with my results. But i have problems in tight places. I own a small 2 man shop where i make custome furniture and cabinets. I know larger shops use pressure pots. Now i know nothing about these...are they basicallt a bigger resevoir to hold material and the finish is pumped to the gun? If so this would alow me to spray in tighter areas at any angle right? Any info would be great

I've never used an Earlex system, but I've used a pot system for years.

Basically the pot holds the fluid, and depending on the viscosity of the material you're spraying the pressure to the pot is adjusted to give a proper flow to the gun. On the gun itself, you are able to fine tune the amount of fluid (flow), air pressure and spray pattern which all play into the atomization you get when spraying (it sounds more complicated than it really is, but it does take a bit of practice to learn the combo's that give the best results)..

From the little bit I just looked at on the Earl's here are the differences that I notice right away..

On a pressure pot setup:

- The gun is much smaller making it easier to get into tight spaces

- The gun is able to be held at any angle without concern of the fluid draining or pulling air (dry spray). Upside down is not an issue :-)

- more adjust-ability with spray pattern, flow and air pressure

- generally speaking a higher quality gun is matched with a pressure pot setup. This is a big factor; you get what you pay for (at least in my experience)

A couple of drawbacks on a pressure pot:

- cost (a good setup between the pot, hoses and gun can easily cost $500 - $1k) This is strictly for a pot and gun, NOT a pump setup..

- compressor size. You'll typically need a compressor that can handle a minimum of 10cfm or more (a little pancake model will not handle the air demand for more than 30 sec)

- More care needs to be taken with air quality; In-line filters both for moisture and oil. Not a big deal, but it's an added initial cost..

- There is typically more material loss (waste) with priming the fluid lines, dialing in the spray pattern and cleanup. Also, the longer the supply lines, the more loss / waste you'll have priming and cleaning.

If the switch is something that you're interested in, contact a rep for one of the gun manufacturers (Bink, Kremlin, etc) and they may have a local salesperson that can come to your site and give a demo.. Kremlin did that for me and the closest rep was 4 hours away.. Needless to say I felt a little obligated to buy something on the spot (BUT he gave me a good deal!!)

Hope this helps a little :-)

  • Author

huge help...thanks alot...one thing you didnt tell me...are you happy with your desision? cost is always an issue but im doing this for a living and anything thats going to save time and give me superrior results im interested in and not afraid of opening the wallet

For my application there was no doubt, yes it was the right thing to do. But I guess I would ask yourself a few Q's before pulling the trigger (no pun intended :-)

- for the amount of volume you do is the cost justifiable? Figure between a compressor, wiring for the compressor, misc filters, gun, pot, hose, etc $2k minimum. Might there be a way to do some pre-finishing before assembly to work around some of the issues you're running into with your current setup?

- Does the price point of the items you're selling justify high end finishes? Sometimes it does, sometimes it doesn't..

I wouldn't expect a pressure pot system to necessarily save you time or material cost, but it will give you better results. In actuality, unless you're spraying for hours at a time and NOT having to break down and clean frequently, it will probably cost you a little bit more in T&M, but the quality will be there.

How about trying to do as much prefinishing before assembly as you can? Switching to an LVLP spray gun can help reducing turblience. :)

  • Author

I think I have the compressor set up...I assume a 60 gal would be sufficient. But i see what you are talking about with cost. I hate pre finishing parts...I know some times its the way to do it but its a pita. I do need high quality finishes...All the info you sent me is a great help...I think the best was to call a company and ask for the area rep...thanks alot

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.