Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Hand rubbed finish... couple of questions...

Featured Replies

Hello all--

I just applied the last coat of Arm-R-Seal gloss on a vase I turned recently. The instructions on the can say to not buff the final coat. I would say the finish is about 80% awesome, but there are some imperfections (dust particles and the like).

So I think I would like to try to hand rub the finish. The problem is that I don't really know what I am doing. The best instructions I have to this point are to dip 1000 grit in soapy water and sand. Squeegee off and do the same with 1500 and 4000. I feel like I have tried this before and ended up with a cloudy finish.

What am I missing here? I don't feel real confident that the instructions are correct or I am understanding them incorrectly.

I also have micromesh sheets I can use.

Finally, do I end up buffing at the end, or does the sanding get to a gloss?

Can someone give me a shove in the right direction? I would really appreciate it!

Thanks,

scott

  • Author

I think part of my problem is that I need to let the finish fully cure. So while I'm still letting that happen, perhaps some people have some ideas how to rub out the final part?

I found one guy suggesting on another site to take a brown paper bag and rub the piece down. I have no idea how that works.

How did you apply the finish (hand or brush)? I've never worked with arm-r-seal but finishing is somewhat universal across most of the products. Just going off of your description what I would suggest would be to let the finish cure for a few days, then wet sand the surface with 320 or 400 until the surface is flawless (dust specs are gone, any ripples sanded smooth, etc) and you're left with a uniform cloudy surface. You could also dry sand but I think I would then go with 600 grit..

After drying either blow the piece clean with air or use a tack rag. Rub a final coat thinned roughly 50/50 with an appropriate thinner using a lint free cloth. If you stick with the arm-r-seal line I believe the thinner would be mineral spirits. It would also help to use a satin or semi gloss product rather than gloss. The higher the gloss level the more any imperfections will stand out.

I'm sure someone will chime in that has much more experience with arm-r-seal then me, but this is how I would approach it :)

Possibly another approach would be to work through the sanding grits up to 2000 and simply rub in a good wax finish (rather than re-applying another coat of arm-r-seal). This should provide a nice satin finish that is flawless, but you may have to re-apply a thin coat of wax from time to time to maintain appearance.

  • Author

Interesting. I know the can says to not thin, but that may be only for a sttandard application layer. But the idea does sound interesting.

So 2000 grit isn't a glossy finish? What grit would be glossy?

If you're a Guild member, Marc has a video on rubbing out a finish with rottenstone. Think that was the wall-hanging cabinet.

And here's a Charles Neil video...

Ultimately I think it depends on what you are looking to achieve for a finished appearance (and that mostly boils down to personal preference). The way I typically finish interior pieces is to a semi-gloss or satin appearance. Exterior stuff that is more decorative (meaning that it mostly gets looked at; not sat on, or handled at all) I'll finish to a high gloss.

If your current surface has quite a bit of dust, brush strokes, etc there will be quite a bit of sanding to remove all of that (and hopefully you don't accidentally sand through your finish :o ). You could actually continue sanding through the various grits to achieve a semi-gloss appearance without having to apply more material; by hand I would probably work up to 2000 grit; if you're using a machine then 1200 would give comparable results. Personally unless there is currently a fairly thick film on the vase all the sanding with the various grits makes me a little nervous.

I typically Err on the side of caution and only sand as much as needed to remove the imperfections, then apply a final top coat to fill the scratch marks left behind. Less sanding means less chance of accidentally sanding through. The reason I had mentioned thinning the arm-r-seal down was to make it more of a wiping finish. All the thinner does is maintain a longer "open time" before the surface starts to skin over (but it also means that you're applying a much thinner film). By wiping the last coat you typically have more control than if you were to brush.

Typically the instructions on a can in regards to thinning mostly pertain to VOC regulations / compliance (not always, but more often times than not). You can thin almost any finish (even if it's not recommended); you'll just have to apply more coats to achieve a comparable film thickness..

Getting a good finish is something that takes practice; both in technique and learning how to work with the product. The nice thing about it is that if you try something that doesn't work out, you can always apply another coat and try again :).

The key to all of this is letting everything cure so that it's hard and able to be worked / rubbed out. If the top film is still soft no matter what method you try it won't work too well. Some finishes are fully cured after a few days, others can take weeks. When you're sanding if you're getting a nice dry powder without gumming up the paper then it's fully cured. If not then it needs more time.

I'd love to see a pic of the vase! :)

  • Author

He also has a video on the free site that explains it.

http://www.thewoodwh...tep-stool-pt-3/

Had not seen this one. Thanks!

.....

After watching this....yeah, this is EXACTLY what I was looking for. Between this and the other advice, I think I have a good idea now.

Now, just time to do it!!

  • Author

And here's a Charles Neil video...

I've seen that video. That's where I started.

You want faster cure and a water-based?

Try General Finishes Wood Turners Finish next time. It's great and cures fast similar to CA glue.

WTF-Quart-250px.jpg

If you need fast grain filling on turned items. Do a couple coats of the General Finishes Enduro Var, then finish out with the Wood Turners Finish.

-Ace-

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.