Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Tablesaw miters: slots vs sleds

Featured Replies

What's better for a tablesaw, a miter slot or a miter sled? I've used both, and for actual miters I like the sled better. But I'm a little worried the lack of a miter slot will greatly limit my options for jigs. What's everyone's opinion on the matter?

What saw are you looking at that doesn't have miter slots?

I have a Craftsmen that does not have a miter slot. DO NOT buy a table saw that doesn't have the slot.

It is a nightmare to try to get consistent mitered cuts without it.

About 5-7 years ago, there was a push to make table saws with sliding tops instead of miter slots for entry level hobbyist table saws. The thinking was that the average Joe doesn't want or need to build jigs. They just use it to straight rip, or can miter using the included miter fence.

The results were near sighted. The sliding table top is nice if you are cutting a board less than the ~20" or so of travel in the top, and only if repeatability isn't important. The plastic miter gauge is sloppy at best. My table saw is definatley on the short list of tools to be replaced!

Yeah I wouldn't even consider a TS without miter slots, either...I can't believe they even manufacture saws without them anymore.

I use my sleds and jigs more often than my miter gauge, but there are times when the MG excels and I'd hate to be without it. So I guess my answer would be "why not both?" Versatility and options are King in my shop. Why limit yourself?

I also much prefer sleds and jigs that ride in the miter tracks than those that ride against the fence.

Spent years with a felder and you certainly don't NEED slots -- but it's a very different way to work.

  • Author

I have a Craftsmen that does not have a miter slot. DO NOT buy a table saw that doesn't have the slot.

It is a nightmare to try to get consistent mitered cuts without it.

About 5-7 years ago, there was a push to make table saws with sliding tops instead of miter slots for entry level hobbyist table saws. The thinking was that the average Joe doesn't want or need to build jigs. They just use it to straight rip, or can miter using the included miter fence.

The results were near sighted. The sliding table top is nice if you are cutting a board less than the ~20" or so of travel in the top, and only if repeatability isn't important. The plastic miter gauge is sloppy at best. My table saw is definatley on the short list of tools to be replaced!

I've had much better experience with mine, but it's probably a later model (the miter fence works pretty well, it's aluminum).

  • Author

What saw are you looking at that doesn't have miter slots?

I wasn't clear in my original post. Some table saws have a built-in sliding table for crosscuts, with a special miter fence. Together they replace cross-cut sleds. Marc seemed to like them in one of his videos, though he didn't go into details.

Spent years with a felder and you certainly don't NEED slots -- but it's a very different way to work.

I think hhh said it better. I learned in my father's shop where jigs were a staple of woodworking. So when I went to a system that didn't have that capability, it highlighted the weakness of all sleds being subject to the fence, or fixed to the top, and subject to a limited slide. I am sure a higher end fence systems may eliminate many of the issues I have (my fence has to be callibrated everytime I moved it), it doesn't latch perfectly square), so I really like the consistency/reliability of the slot. It's clean, it's simple, it's consistant. The slot just always seemed faster and more accurate to me, but that could just be one expereince. Tweaking a fence and rechecking after a few cuts is a pet peeve for me.

There are a lot of accessories and pre-built jigs that won't work without the slot, so that is just one more thing to keep in mind.

The BT3000 was a ryobi saw that used this method with a interchangable sliding table/router plate with a swivel bar for cutting angles.

I have this saw (motor burned up) so I mounted the rails to an older craftsman saw that has miter slots now I have the combination of slots and sliding table(router plate installed in pic). To answer your main question miter slots keep all your options open and provide the most flexability with aftermarket products.

post-5469-0-32008200-1354112777_thumb.jp

==> I've seen a few Euro-table-saws that had the sliding table. But they still had a miter track.

My Felder didn't -- nor did my father's Felder Combo Machine. So may be hit or miss by brand/model.

From my experience, if you don't adopt the Euro saw methodology, then slots are useful for jigs that substitute for a quality sliding table... But it's a different way of working -- not 'better', just different. I sometimes miss the sliding table, sometimes it was a pain in the ass... My only other observation is that a cheep sliding table is more trouble then it's worth -- i'd go slots over a cheap sliding table, if you have a choice...

  • Author

My only other observation is that a cheep sliding table is more trouble then it's worth -- i'd go slots over a cheap sliding table, if you have a choice...

I don't know about that; mine's pretty cheap, and after waxing all the parts of the sliding table it works pretty good (albeit with a very small amount of binding at colder temperatures). On the other hand, I don't use it everyday, and perhaps if I did I'd hate it. You never know.

I had the Ryobi about 14 yrs ago and yes it got the job done but it was very underpowered and the sliding miter table was alright but the lack of being able to have jigs that ride in miterslots did not fair well with me. I built a small section that had a miterslot in it and attached it to the main table, that helped but the saw was still very underpowered for what I build. I think it really depends on what you type of woodworking you do, if you build smaller stuff you may love it. I sold mine and bought a Jet contractor saw then moved up to a cabinet saw but the guy who has my old Ryobi is still quite content with it as he only builds small projects. So I truly believe it's in what you build but the difficulty of building jigs and lack of power can hold you back.

Also, some low end table saws have miter slots that are enough smaller than standard, so that they don't take standard accessories. My 2nd table saw, a $140 Delta, was like that. When I called up Delta they said that if I wanted standard size slots I should buy a more expensive model.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.