Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Screwed up shellac with dye, now want to use water-dye

Featured Replies

Hello everyone,

This is actually my first post here, though I've been lurking for years. I am an amateur banjo builder and I'm working on my latest neck. I usually use shellac as a finish - most usually blonde, but sometime amber. When I've scewed up with shellac in the past, I've just sanded it off and started over. But this time it's different. This time I'm trying to use a transtint dye (vintage maple) and attempting to get my curly maple to be a light brown.

Well, I tried to do this with shellac and it looks awful. After doing alot of reading, I've decided to use the transtint as a waterbased dye.

My question is, how much sanding do I have to do to get below that first coat of shellac. I have all the color off with 180 grit, but I'm assuming there is more still in the grain. Should I go down to 150, 120, 100 (or is 180 good enough?)

Thanks for any guidance.

Jeff

==> Well, I tried to do this with shellac and it looks awful

sorry, but i'm confused as to what the exact steps you took?

shellac, then dye coat, then shellac? or dye mixed into the shellac and applied? or??

Keep sanding till it's gone or mostly gone, light enough to deal with. Between sanding try some denatured alcohol to wipe down the neck to help pull some color up.

Yes drop down to say 100 and go up through the grits. Problem is going to be the shellac has gone down into the curl and will seal it off not allowing your dye to soak into the curl.

Good luck.

Do a little test. Use some regular shellac in a inconspicuous place. Or make a sample from scrap, use the same tinted shellac, let it dry sand it off, then test your new stain and finish combination .

  • Author

Thanks for the replies.

===

hhh, steps were: 1) sanded the curly maple to 180 grit, 2) applied shellac mixed with transtint dye.

Now (because it looked so sloppy) I want to sand off that coat of shellac and start fresh with the same dye mixed in water.

===

wdwerker,

That's what I'd thought I'd do before I posted this question , but then thought I'd see if anyone had experience with this same (or similar) problem.

===

Ace,

I was afraid I might have to go down that low.

Thanks for again for your replies.

Any other ideas out there?

Jeff

===

i frequently tint shellac to even-out a table top, but not on the seal coat. i usually apply a 1 - 1.5 ct SB seal coat, to get any blotch under control, then mix tint with another 1.5ct SB. I typically spray, so the coats absorb evenly.

it's a bit different if i want to pop the grain -- i then apply thin transfast by hand and sand back. then spray 1.5ct seal coat.

it sounds as if you are going to have to sand all the way back, then move back through the grits.

  • Author

hhh,

Do you know what "all the way back" is? Is there a way to test, maybe with water, to see if the grain is raising again?

You may want to use the dye in alcohol, not water. In case some shellac remains in the curl the alcohol with help the dye penetrate through the shellac. Do you have a pic of the color "brown" your trying to get too?

Wondering if a good drying oil may be the way to go?

  • Author

Thanks again hhh and Ace.

I ended up going down to 120 grit and used a waterbased mixture. Looks a million times better. I can't figure out how to post a photo, maybe members have to have X amount of posts first.

Any idea how long to wait before I apply my first coat of shellac?

Jeff

24hrs is usually fine. also depends on your shop's ambient conditions -- my shop's %29RH and 70F at the moment --- transfast dye coats are ready in like 8hrs under those conditions. transtint is like 30 minutes if i spray it.

Just error on the side of caution. A lot depends on the type of wood. Porous woods like poplar pull water or anything in deep, its like a sponge. Can be dry on the surface or to the touch, but still wet below the surface.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.