Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Restoring old doors

Featured Replies

My house was built approx. 1940. Originally it had the old mortise locks on the interior doors, but was "modernized" along the way. They did a really bad job, using a jigsaw to enlarge the holes for the new style door hardware. I am restoring it back to the original style. I purchased mortise locks that fit into the existing holes (they never filled them), and I bought beautiful glass knobs and solid brass back plates from that era. Everything fits great. My question is how do I restore the doors. The plates are small and they do not cover the enormous holes. I have a couple of questions. One is how do I find the correct wood, and is that crucial. Second, can I use 2 sized hole saws, one 1/8" larger then the other, so the fill piece fits perfectly into the hole I drill? Third, since there is a hole already, I need some way of stabilizing the hole saw when I'm drilling. Fourth, I will need to putty a few areas. How do I get a good match to the existing wood? Is it better to tint the putty or try and stain it afterward? I hear the stain usually produces a darker result on the putty than the wood.

Note: I have some painted doors and some that were left with the original finish. I'd like to strip all the doors but that's probably going to be a crazy lot of work. How do I determine what finish is on the non painted doors - varnish, shellac, polyurethane etc.? I will need to re-do the finish of the wood doors after I fix the holes, so it has a more cohesive look.

Any suggestions or advise is appreciated! I have put photos on the web page below since they don't let you upload over 1.46 mb here.

http://www.cleacarchia.com/door/woodtalk.html

Clea Carchia

Rahway, NJ

If I am correctly understanding your question about two hole saws 1/8" difference in size to cut 1. the hole in the door and 2. to cut the plug for that hole. If this is your intent, then your plug will not fit because it will be 1/8" too small. You will need to cut your hole and then make a plug the same size. The question about makeing the hole saw stable is pretty straight forward. You mount two hole saws together....one that is the same size as the existing hole and the second the size you wish to cut. The smaller saw rides inside your existing hole while the other saw enlarges the hole. As far as the wood is concerned, I would try to match if possible or if nothing else come close to something that can be colored to match. Hope this is of some help.

Just looked at your pictures....whoever did that to your beautiful doors should be taken out and shot!

To restore old doors you steal wood grafts out of the corners as needed. You make 45 degree cuts into the corner edges spaced as wide as needed. Use a coping saw to remove the triangle grafts. Fill all mortices and bores back to solid wood, this means Re mortising oversized. Once they are filled with a new hardwood tenon you can easily install your graft inlays. Once you refinish and stain match to your millwork no one will be the wiser. The grain of your grafts will be slightly off but the wood match will be perfect on the face.

Don

Fixing those doors and getting an acceptable match to the grain is very hard to do.

Wonder what the chances are of finding sets in an architectural salvage shop. They were very common and often replaced by renovators or salvaged when houses were torn down. You might find some in good shape fairly cheap.

The simplest way to drill a hole with a hole saw, when there is no wood there to hold your pilot bit, is to bore a hole in another piece of wood, clamp that to the door and use it as a guide for the new hole. It's best to mark your center lines before you bore the template so you can align the remaining marks with the center line on your door stile. Hope that made sense.

  • Author

Thanks guys for repying to my post. It gives me a little to think about. I'll post some before and after photos!

Clea

  • 3 weeks later...

Your photos make it appear that your door is veneered. Is this the case? If so it may be wise to consider a much less time consuming but more aggressive repair leaving the only trick to be the matching of grain with new veneer stock.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.