Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Attaching veneer to substrate

Featured Replies

So I have a few projects drawn up and I would like to incorporate some veneer patterns. My question to everybody is how to attach them?

I have read that some folks use white glue and lots of weight/ clamps.

Other swear by home made vacuum bags and special veneer glue

In some books, I have seen hide glue and a veneer hammer for smaller components such as drawer boxes.

If i were to apply maple or walnut veneer to say a 24" x 24" table top, what would be choice method?

I've done a lot of veneer work and used contact cement. I know that's not the method talked about here so often, but it's simple and works for me. Apply contact to both surfaces, let it dry until it doesn't stick to your fingers when you touch it. Then apply your veneer and roll out with a rubber roller, exerting as much pressure as you can. If you don't have a rubber roller, make a rubbing block out of a soft wood like cedar or mahogany by sanding one end round. Make it narrow enough that you can hold it easily in your hand and rub the veneer out using the rounded end.

There's lots of ways to apply veneer. Without spending anything on new equipment you can water down some yellow glue 50% and paint it onto your veneer. Let it dry. Spray the show side with water and put it on your substrate, then just iron it on.

So I have a few projects drawn up and I would like to incorporate some veneer patterns. My question to everybody is how to attach them?

I have read that some folks use white glue and lots of weight/ clamps.

Other swear by home made vacuum bags and special veneer glue

In some books, I have seen hide glue and a veneer hammer for smaller components such as drawer boxes.

If i were to apply maple or walnut veneer to say a 24" x 24" table top, what would be choice method?

I would use a vacuum bag and the proper glue. Contact cement is the worlds worse way to apply veneer. Veneer comes in many variations (paperbacked, two ply .......) What glue you use is determined by the type of veneer. Regular yellow or white glue is to soft and leaves you with visible glue lines over time.

If you want to learn about veneer prior to starting your project go visit joe woodworkers web site. Lot of good information along with the necessary supplies at an affordable price.

Don

  • Author

I would use a vacuum bag and the proper glue. Contact cement is the worlds worse way to apply veneer. Veneer comes in many variations (paperbacked, two ply .......) What glue you use is determined by the type of veneer. Regular yellow or white glue is to soft and leaves you with visible glue lines over time.

If you want to learn about veneer prior to starting your project go visit joe woodworkers web site. Lot of good information along with the necessary supplies at an affordable price.

Don

Great advice, thanks

 

Contact cement just won't work for me.  In school we were taught to never ever ever do that.

 

The veneer I am planning on using is plain veneer, no paper backing or anything -just the veneer.

 

Also, in the past I have used a vacuum bag and rolled on veneer glue(titebond if i recall) however I do not have access to that equipment anymore.

Don, what is the reason for not using contact cement? I've never had a problem with it.

  • Author

Don, what is the reason for not using contact cement? I've never had a problem with it.

After reading my old notes, the reason contact cement should not be used is its cohesive properties. It is very cohesive but not very adhesive

Contact cement sticks to other contact cement very well however the bond between the layer of contact cement and the other surface is very weak.

 

Also it does not harden like say hide glue or pva/polyurethane glue. This property is a huge disadvantage for veneer- it would dent easier than veneer attached with another type of glue.

Not to mention seasonal movement.

 

HOWEVER

 

contact cement CAN be used on sheets of veneer which have a backer as this will minimize but not get rid of movement

A

HOWEVER

contact cement CAN be used on sheets of veneer which have a backer as this will minimize but not get rid of movement

Can and should are two different things. Longevity is the key here.

Veneer creeps that is just the way it is backed or not. Veneer glue is hard, very hard. Since it has to be purchased in gallons a substitute is plastic resin.

I tried to get a pic of how the texture ws completely different than yellow glue.

This cabinet door i pressed would have a glue line at a few months old right down the center and around all the edges where it meets the banding with yellow or contact. This one is a reject and has been in the burn pile for months. (Finish has slight blush)

Paper back is not what it sounds like. Veneer is stitched with either glue or glue and string. After the glue is dry the string is removed. Picture grandmas old zigzag sewing machine with no needle with string covered in hot melt glue. Then the veneer gets surfaced on the back with paper fiber impregnated resin. It's very thin not like a sheet of paper stuck on the back. This holds the veneer together and makes it more usable it does not block out chemicals of the glue. The Resin is dyed to match the species.

This is walnut back.

This is maple back, notice how nice it is to work with. Just roll and store.

  • Author

Can and should are two different things. Longevity is the key here.

 

Incorrect- If I were to build a set of stairs - walnut steps for example and wanted to use veneer for risers, for cost reasons this would not be an issue as lots of trim pieces would be covering the edges.  In a pinch i would use it but not my first choice.

Veneer creeps that is just the way it is backed or not. Veneer glue is hard, very hard. Since it has to be purchased in gallons a substitute is plastic resin.

 

The reason veneer creeps is because the wrong glue is used(PVA, or "carpenters glue")or it was not in a controlled climate etc.etc. etc. Veneer glue prevents that.

I'd rather purchase the correct product and most of the time you will use that gallon up in a project or two.

 

Also plastic resin contains urea formaldehyde - something I don't want to be around- not to mention the insanely long clamping time required

Here is a quote from David Marks website.

"Once you have created your full sheet, it will need to be glued up. I do not recommend using contact cement as an adhesive because it remains flexible. Yellow Aliphatic resin glue works, but I believe the best results are obtained with slow setting Urea resin glue. My favorites are URAC 185 and Unibond. Good results can also be obtained with Weldwood plastic resin glue. "

Bag time for unibond is minimal, no more than pva. The glue isn't dangerous unless you're eating it. If you buy the powder form a dust mask should be used for mixing but after its wet your good. Probably much safer than solvent based contact cement. The WB will wrinkle your veneer, to much moisture.

Don

  • Author

Here is a quote from David Marks website.

"Once you have created your full sheet, it will need to be glued up. I do not recommend using contact cement as an adhesive because it remains flexible. Yellow Aliphatic resin glue works, but I believe the best results are obtained with slow setting Urea resin glue. My favorites are URAC 185 and Unibond. Good results can also be obtained with Weldwood plastic resin glue. "

Bag time for unibond is minimal, no more than pva. The glue isn't dangerous unless you're eating it. If you buy the powder form a dust mask should be used for mixing but after its wet your good. Probably much safer than solvent based contact cement. The WB will wrinkle your veneer, to much moisture.

Don

Who uses solvent based contact cement anymore? Or or urea formaldehyde? In the industry, water based contact cement is pretty much standard and as for the

urea formaldehyde -Its terrible stuff AND not to mention I wouldn't want that stuff anywhere near kids.

 

I don't disagree that these methods or your ideas will not work, however I feel that what I am suggesting is a better method and less of a hassle- whether it be personal or commercial.

My idea is to use a vac bag and Titebond cold press veneer glue. It is brown in colour to blend in, has good gap filling properties and dries extremely hard to prevent movement.

to apply the glue i will be using a glue roller applicator similar to this:

DSCF2050.jpg

the workpiece only has to be in the vac bag for 1-2 hrs.  This way I won't have to use as much electricity to power the compressor compared to longer clamp times with other adhesives.

Who uses solvent based contact cement anymore? Or or urea formaldehyde? In the industry, water based contact cement is pretty much standard and as for the

urea formaldehyde -Its terrible stuff AND not to mention I wouldn't want that stuff anywhere near kids.

I don't disagree that these methods or your ideas will not work, however I feel that what I am suggesting is a better method and less of a hassle- whether it be personal or commercial.

A guy can use whatever he wants you don't need to convince me. It's your thread you asked the question, I guess you answered it for yourself. If you want to use contact no one is stopping you. You asked "what would be the choice method". The answer is the proper glue and a bag or frame press backer or not. If you have veneer pressed doors in your house then your already exposed, we used that glue by the truck load and the plant I was a joiner at is still using it today pressing a million doors a year being shipped all over the world. :)

Tb is just Pva, no its not hard. It's made for hpl and backed veneers preferably phenolic backed.

Don

  • 3 weeks later...

I've done a lot of veneer work and used contact cement. I know that's not the method talked about here so often, but it's simple and works for me. Apply contact to both surfaces, let it dry until it doesn't stick to your fingers when you touch it. Then apply your veneer and roll out with a rubber roller, exerting as much pressure as you can. If you don't have a rubber roller, make a rubbing block out of a soft wood like cedar or mahogany by sanding one end round. Make it narrow enough that you can hold it easily in your hand and rub the veneer out using the rounded end.

 

Relived to hear someone else does this. Although we don't do lot's of cabinet work we used your method when we bonded the veneers to these stair strings veneer supplier said you are not really supposed to but nearly all of their clients do it this way.

Thanks, GS. I've been using contact for over thirty years and have never had a call-back. I have furniture in my own home that I veneered over twenty years ago and it's as good as the day I did it. I guess I'll just have to live with the fact that I'm not a purist. I think I can handle the shame.

Thanks, GS. I've been using contact for over thirty years and have never had a call-back. I have furniture in my own home that I veneered over twenty years ago and it's as good as the day I did it. I guess I'll just have to live with the fact that I'm not a purist. I think I can handle the shame.

If you were a purist you would use hide glue. :) WB contact has only been one the shelf for 22 years and has only been approved for commercial application for about 20. Rubber cement and contact cement are two different glues. Rubber cement has been around for about 100 years.

Don

Thanks, GS. I've been using contact for over thirty years and have never had a call-back. I have furniture in my own home that I veneered over twenty years ago and it's as good as the day I did it. I guess I'll just have to live with the fact that I'm not a purist. I think I can handle the shame.

No shame, we were shown by a guy who made these incredible stairs . I have updated the link in my original post (I assumed a copy and paste weblink would work). Take a look at what we do and let me know what you think. And just to clarify this is the glue we used as did he on many projects without problem. Perhaps it would not be suitable in all applications but it worked well on this one.

Nice looking stairs, GS. I've got a set that I did on a post about bent wood, somewhere here on the forum. I love doing staircases.

Sean, If I was going to veneer a pattern top with maple or
walnut I would use the Urea formaldehyde glue. Mainly because I am a firm believer
in a rigid glue line and the other hard glues can be a mess in themselves. I
know the word formaldehyde is scary but remember it has only 2 to 4% added in
the total mix. So wear a good dust mask and gloves when mixing it. Also your comment
in this post, “it’s brown in color to blend in and has good gap filling
properties and dries extremely hard to prevent movement.” Yes, you are describing
u/ f glue! As for pressing I would use a vacuum press.  I know other have their opinions And that fine
but I look at it this way I can spend 3 to 8 hrs on a face layup and to lose it
because of the glue no way.    Tom 

  • 4 weeks later...

I use Titebond II all the time and never had an issue. Since I spray with water-based dyes, the Titebond II holds up while the wood is damp. I use my vacuum bag occasionally, but to save time I will just clamp up the piece for an hour.

 

I use veneer and reclaimed wood to economize. I like to create Arts & Craft style furniture, so I use a lot of oak. A recycle center close to me sells reclaimed oak flooring at a fraction of the cost of new hardwood. I laminate pieces together to create thick stock and to hide the sandwitch, I glue on quarter-sawn white oak. I like to mix wood species together too. Here is a table with a ash veneer center surrounded by cherry veneer.

  • 3 weeks later...
  • Author

Nicely done rglissmann. With proper grain orientation, you can create stock which looks very close to solid wood

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.