Recommended Posts

Posted

Hi all,

 

I just bought a Grizzly 8" jointer (G0490X) a couple of weeks ago.  I'm thrilled with the purchase so far, other than setting up the fence square to the tables.  I've been searching for advice online, and most of the reviews say something like "setting up the fence is a bit clumsy."  That might be the understatement of the year.

 

I'm hoping someone on here with the same jointer can help me out.  I loosen the set screw on the cam that controls the 90deg stop.  I then loosen the lock handle.  At this point the Fence moves in two "dimension" (not the right word but hopefully people with this machine will know what I mean).  You have the axis that attaches the fence to the fence carriage, and then you have the axis that lets the fence rotate.  With these both moving simultaneously I find it basically impossible to get it to line up perfectly with my square.

 

The other thing is, even once you've set up the 90deg stop and tighten that set screw, if you ever loosen the lock handle (or it becomes loose over time) the fence will "fall" toward the table because only one of the axes I described above is locked (the one with the plunger locking in the 90deg stop). 

 

Can someone break this down for me?  I know I'm probably not explaining this well.  I will try taking some pictures to supplement if people don't know what I'm talking about.

 

Thanks a lot in advance.

Posted

I don't have that jointer, but I can offer some general technique.

 

I move the fence to the fore / aft position I plan to use, lock it, then set the fence angle.  I place my square on the outfeed table, directly to the left of the knife opening, slightly loosen the angle lock, set it, and retighten.  I only use the 90 stop for "general" work, setting directly to the square when it counts.

Posted

The problem is really not a problem. If your fence is off slightly you really dont need to loose sleep, close is close enough. When you edge joint a board your doing it to straighten the board or prepare it to be edge joined to another board. If you assume up front that your jointer is off you will never have a problem. When you edge joint a group of board you ALWAYS flip the face assuming the jointer is off.

XOXOXOXO

OXOXOXOX The "X" goes against the fence. Even if its off a hair the opposing angles will always match perfectly.

Posted

I have the same jointer and struggled a bit also with the setup of that fence.  I got mine used, so I spent time aligning everything.  I think the key is patience and checking for square at several points along the fence.  Ultimately, I got it very close, which as the previous poster pointed out is just fine, when you follow the strategy of assuming it is slightly off.  I spent a lot more time getting the two tables to be perfectly aligned.  Using a 4ft aluminum straight edge made for precision and automotive feeler gauges (and this awesome tutorial http://www.thewoodwhisperer.com/videos/jointer-setup/) it was manageable.  Then I picked up the A-LINE-IT Deluxe Kit to get the knives setup right (but this tool also helped me get the tablesaw and drill press set right).

 

Overall, the time spent with setup has been well worth it, the tool is perfect everytime.  You'll love it.

 

Posted

 

 

 

Thanks everyone for your responses.  The "little bit off" thing makes sense to me, and I will keep that in mind as I prepare panels for glue up.

 

Chris - am I right that the 90deg stop is pretty much useless given that if you loosen the handle to allow the fence to rotate, it will still "fall" because it's rotating around that other axis?  Do you know what I'm saying and is that correct behavior of the fence?  Basically the only think holding it square to the table is that black handle.  I'm going to try to get some pictures tonight.

Posted

I have that jointer...it's a lousy design.  I got mine dead at 90, locked it down hard, and never touch it.  I don't rabbet or do anything else with it, so it's fine for me.  Vic said he's gonna have a welder tack his in place...I may do the same thing.

Posted

I have that jointer...it's a lousy design.  I got mine dead at 90, locked it down hard, and never touch it.  I don't rabbet or do anything else with it, so it's fine for me.  Vic said he's gonna have a welder tack his in place...I may do the same thing.

 

Cool, so I'm not crazy.  It is a very lousy design.  I will get it to 90 and lock it down hard like you did.  I won't be using the jointer for anything else either.  I'd be a bit wary of welding it in place though, as you might have an issue if the tables ever move out of parallel and you have to adjust them.  It would be a pain then with an immobile fence because you'd have to adjust the tables 90deg to the fence rather than vice versa.  Unless I'm misunderstanding something.

Posted

Cool, so I'm not crazy.  It is a very lousy design.  I will get it to 90 and lock it down hard like you did.  I won't be using the jointer for anything else either.  I'd be a bit wary of welding it in place though, as you might have an issue if the tables ever move out of parallel and you have to adjust them.  It would be a pain then with an immobile fence because you'd have to adjust the tables 90deg to the fence rather than vice versa.  Unless I'm misunderstanding something.

 

Good point!  Nevermind that.  LOL

Posted

Nick I just bought the g0490 myself. I did find the fence adjustment to be a pain in the rear. But I fiddled with it, and got it pretty close. I can't give any advice b/c I think I just got lucky lol.

Posted

I have a Grizzly jointer, and I found that when moving the fence across the table (not tilting) it still moves a little out of square. Just a little bit, but enough to notice with a square. So I reset the fence as wide as it will go, and locked it down so it will not move in the immediate future. Perfect cuts ever since.

 

I paid $720 for an 8" jointer with 72" beds. With the amount of money I saved over buying a Powermatic or Delta, I can live with this for now. Would I have liked to get a Powermatic or Delta, you bet. But was it affordable to me at the time? No.

Posted

That was my exact reasoning for buying this jointer.  My work was suffering from not being able to get my stock nice and square.  I have a planer, but getting that first edge flat, even with a sled, was PIA and it never got quite dead flat.  The Grizzly was half the cost of the PM.  I'd rather have the PM, but I'd rather save that cash for a table saw upgrade next year or the year after (I'm still working on a jobsite type table saw, which is very limiting.  I want to upgrade to a PM2000 or sawstop, and that's not happening if I drop 3 grand on a jointer right now). 

 

I'm still very happy with the purchase.  There are definitely some annoying things (the fence, and the table height adjustment mechanism is clumsy, the fit and finish leaves a bit to be desired) but it cleanly and quickly (and quietly!) flattens boards.  That's all I need.

Posted

Are you guys talking about the fence going out of parallel with the bed edges, but staying square to the table?  As in one end of the fence is closer to the front of the machine than the other?

 

If so, no worries!  MANY jointers do that, and it's not a concern at all.

Posted

...There are definitely some annoying things (the fence, and the table height adjustment mechanism is clumsy, the fit and finish leaves a bit to be desired) but it cleanly and quickly (and quietly!) flattens boards.  That's all I need.

 

Exactly.  Buying a high-end jointer is a waste of money, IMHO, since as long as everything is flat (enough) when it arrives, and you set it up dead square and coplaner...and it stays that way...who cares?  It's a one trick pony...as long as it flattens and squares, where does the extra money for the PM or Delta pay off?  Because it looks cool?

 

Other tools, different story.  But jointer and planer, I don't get the love affair with paint colors.

 

 

 

Are you guys talking about the fence going out of parallel with the bed edges, but staying square to the table?  As in one end of the fence is closer to the front of the machine than the other?

 

If so, no worries!  MANY jointers do that, and it's not a concern at all.

 

No, not that...the adjustment to get the fence 90* to the table is awkward and fiddly...but not impossible, and as long as you're not adjusting the fence for different functions all the time, it's no big deal.  Where's that slogan come from?..."set it and forget it?"  That's what I did. :)

Posted

Exactly. Buying a high-end jointer is a waste of money, IMHO, since as long as everything is flat (enough) when it arrives, and you set it up dead square and coplaner...and it stays that way...who cares? It's a one trick pony...as long as it flattens and squares, where does the extra money for the PM or Delta pay off? Because it looks cool?

Other tools, different story. But jointer and planer, I don't get the love affair with paint colors.

No, not that...the adjustment to get the fence 90* to the table is awkward and fiddly...but not impossible, and as long as you're not adjusting the fence for different functions all the time, it's no big deal. Where's that slogan come from?..."set it and forget it?" That's what I did. :)

Ron Popeil?
  • Like 1
Posted

Exactly.  Buying a high-end jointer is a waste of money, IMHO, since as long as everything is flat (enough) when it arrives, and you set it up dead square and coplaner...and it stays that way...who cares?  It's a one trick pony...as long as it flattens and squares, where does the extra money for the PM or Delta pay off?  Because it looks cool?

 

Other tools, different story.  But jointer and planer, I don't get the love affair with paint colors.

 

I dont think its a love affair with paint color nor is mustard cool its sort of ugly. :) Some of us buy tools with the expectation to be able to use them and all their features. I move my fence every day. I move my infeed table daily. I move my fence in and out every so often to spread out cutter wear. I cut bevels almost daily. I taper tablelegs. I rabbet daily. I make t&g tongue side joints. I lip plane hardwood edge banding. I lip plane wood and plastic glue on eged banding daily.

IMO its a bigger waste of money to buy an expensive tool and condemn it to the life of a "one trick pony" when it does more faster and better than any other tool in the shop. IMO your better off looking for a way to fix your jointers issues and use it for all its worth.

Posted

PB - if I did all that I would most certainly have made a different purchase.  But when I make rabbets I prefer to use the router table or table saw.  Table saw for bevels too.  For table legs I use the table saw with shopmade tapering jig or my planer.  It also sounds like you're churning out a lot more work than I am - I'm lucky to squeeze in one complete project every couple of months :)  So for me the cost savings was definitely worth it as long as I can square my stock. But I definitely see and understand the use cases you mentioned for a more production level shop (or a hobbyist who is able to squeeze in more shopt time than I).

Posted

PB - if I did all that I would most certainly have made a different purchase.  But when I make rabbets I prefer to use the router table or table saw.  Table saw for bevels too.  For table legs I use the table saw with shopmade tapering jig or my planer.  It also sounds like you're churning out a lot more work than I am - I'm lucky to squeeze in one complete project every couple of months :)  So for me the cost savings was definitely worth it as long as I can square my stock. But I definitely see and understand the use cases you mentioned for a more production level shop (or a hobbyist who is able to squeeze in more shopt time than I).

Im not saying you didnt make a good choice nor am I knocking Griz. With most everything if there is a will there is a way. Im just saying spend a few dollars on some hardware and fix the tiny fence issues so you dont have to deal with the problems. 9 times out of ten its just a matter of adding a better knob or washers something along that line. Do give tapering table legs a try though they are much easier and more accurate on your jointer and you can do all four sides with one set up. :)

Posted

When you taper legs on the jointer, do you typically taper an entire side first, or do you do one pass on each side kind of rotating it around until you have the taper depth that you want?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   1 Member, 0 Anonymous, 43 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,009
    Total Members
    3,644
    Most Online
    Joseph b
    Newest Member
    Joseph b
    Joined