WelshWood Posted June 24, 2013 Report Posted June 24, 2013 Hey there, So I'm reluctantly selling this bit of kit as it's taking up to much space in my small workshop. It was given to my father some years ago and was used a couple of times, but since the passing of my father in '09 it hasnt seen any use, I'm looking to sell it so was wondering if any of you give some more information on it, and if possible, to give a guideline price if I was to sell it, Many thanks! ~WW Quote
TerryMcK Posted June 24, 2013 Report Posted June 24, 2013 Hi WW. If you are based in the UK then have a search on the UKWorkshop forum as somebody was selling similar machines back in 2010. On this forum people call them jointers. It would help if you had a few measurements of the cast iron table and fence too. Quote
EdgewaterWW Posted June 24, 2013 Report Posted June 24, 2013 It's a Multico Surface Planer (maybe model 250), A model 250 sold on the UK Ebay for £250.00 back in 2011. Measure the Cutter Head to find out if it's a 6" or 9" (100-150mm) model. Quote
G S Haydon Posted June 24, 2013 Report Posted June 24, 2013 Hello WW, Multico is ok but not a brand I jump for. That said it's an older machine so likely to be very robust. Like Terry says try UK workshop or try e-bay. I'm sure it would serve someone very well indeed. Quote
WelshWood Posted June 24, 2013 Author Report Posted June 24, 2013 Thanks for the great replies guys, just re-measured it and it's the 9" model, found the serial number on it too which should help me out somewhat! Hello WW, Multico is ok but not a brand I jump for. That said it's an older machine so likely to be very robust. Like Terry says try UK workshop or try e-bay. I'm sure it would serve someone very well indeed. Robust?! I can barely move it haha! t When you say it's on okay brand are we talking black and decker standard? Amongst all the tools in the workshop I inherited, I have a record power bandsaw & pillar drill, fox hollow chisel mortise and a few sanders.. As a site carpenter i'm not used to using these joinery machines, so are these reputable brands or entry level standard? (My father was more of a serious hobbyist rather than a carpenter so to speak) Thanks for your great help once again! ~WW Quote
G S Haydon Posted June 24, 2013 Report Posted June 24, 2013 WW, Multico to my knowledge never made large joinery machines. That's not to say there bad quite reputable in fact, just a bit more entry levelish/one man band type thing, which is fine. Not an old Wadkin if you like. I'm sure it will be an asset to it's new owner. Quote
WelshWood Posted June 24, 2013 Author Report Posted June 24, 2013 WW, Multico to my knowledge never made large joinery machines. That's not to say there bad quite reputable in fact, just a bit more entry levelish/one man band type thing, which is fine. Not an old Wadkin if you like. I'm sure it will be an asset to it's new owner. That's the initial feeling I had to be honest, as I said, more of a hobby workshop, Will take a good bit of careful planning for me to make the most out of the space I have available to me! With regards to the record power machines, what are your views on them? If I do end up selling it, I'll probably be looking to replace it with a planer thicknesser. Are there any particular brands or models that you could recommend? (not looking to spend thousands on it as like I've stated, i'm more of a site carpenter, but would like to think a few hundred spent on a machine would be a good investment) many thanks, ~WW Quote
dwacker Posted June 25, 2013 Report Posted June 25, 2013 Multico was a door shop staple years ago. Their tenoners were all over the world. Looks like they are now just hanging on by a thread. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.