lemonjello Posted June 26, 2013 Report Posted June 26, 2013 I own four Festool tracks and my two older ones have a black rubber strip and two newer recently bought ones are translucent silicon. The silicon ones are delaminating from the track! the older black rubber ones are fine. Anyone else have this issue? I have replaced one with a brand new "replacement" strip and I noticed yesterday that the entire thing pealed off and laying on the floor!!(hanging vertical on the wall). I've emailed Festool and no reply yet, but I figure it may take awhile. Quote
Trip Posted June 26, 2013 Report Posted June 26, 2013 ==> I have replaced one with a brand new "replacement" strip and I noticed yesterday that the entire thing pealed off I've replaced a few of these strips over time... The first one started pealing-off. I was told to clean the back of the track with some PVC pipe joint cleaner. I haven't had pealing issues since... Quote
Freddie Posted June 26, 2013 Report Posted June 26, 2013 TripleH, sounds like I have to try that. I just replaced mine. I cleaned the track with acetone as directed on the splinter guard box. It started to peel the next day, wth. No intention of hijacking this thread, but for you guys how long does your new splinter guard last before it starts looking a little uneven? Mine was just replaced and it seems to already have an uneven edge along its length. Quote
Trip Posted June 26, 2013 Report Posted June 26, 2013 ==> but for you guys how long does your new splinter guard last before it starts looking a little uneven? uneven as in it's slipping on the track or uneven as in cutting of the strip by edge tools? I use my track with TS55, TS55-R, TS75 and a couple of FT routers so my strips get ratty pretty fast... I only replace them when they start to peel-off. ==> acetone I think that PVC cleaner is ever more powerful -- I also scuff-sanded the track bottom where the strip mounts.... Quote
Freddie Posted June 26, 2013 Report Posted June 26, 2013 Thanks H, i only have the ts75 that gets used with my 2 rails. For only using one tool on the rails i cant understand why the edge gets snotty so fast. Quote
Trip Posted June 26, 2013 Report Posted June 26, 2013 ==> i cant understand why the edge gets snotty so fast My TS75 has significantly more 'play' than either my TS55 or TS55R. I understand that this is a common complaint with the TS75 -- but it's still minor... I usually clamp my track to the work surface, so there is no movement of the track itself... So if you also clamp the track and still get quick 'snotty edges', then you may have more play than average. Your TS75 should also give clean cuts, just not a clean as a TS55/R, but I can see where the TS75 would go through a track strips faster than a 55. Quote
Freddie Posted June 26, 2013 Report Posted June 26, 2013 Thank you tripleH for explaining that to me, that makes sense. I went thru my dealer asking why that happened and i got more or less an attitude and the fact that they couldnt find a problem, but no explanation, so i always wondered. Thank you. Quote
lemonjello Posted June 28, 2013 Author Report Posted June 28, 2013 Update: I did get a call from Festool (Steve), unfortunately I was in meetings during his call. I am hoping for some good news, was quite surprised to get the call actually. Will know more when I call back tomorrow! Quote
pghmyn Posted June 28, 2013 Report Posted June 28, 2013 I probably haven't cut as much as you guys, but I've made at least 100 cuts with my TS55 and the splinter guard still looks freshly cut. I also have the black strips on the back that are still like brand new. Just got a new blade on my saw and it cuts like a dream again! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.