EdgewaterWW Posted July 16, 2013 Report Posted July 16, 2013 I was at a lager FESTOOL dealer (retail and online) and found out about the recall. This is not a recall to the consumer at this time, But this major store had to ship back over a dozen saws back to FESTOOL. The problem is with the retractor (the floor manager called it) blade not retracting as it should. I found some posts on FOG that confirm this. Quote
EdgewaterWW Posted July 16, 2013 Author Report Posted July 16, 2013 From the Admin at FOG. "Festool has notified the Consumer Product Safety Commission (CPSC) and Health Canada of a potential problem with the plunge mechanism on some TS 55 REQ Plunge-Cut Track Saws. While investigation is continuing, Festool, in cooperation with the Consumer Product Safety Commission (CPSC), intends to recall affected units. If you have a TS 55 REQ Plunge Cut Track Saw, please discontinue use immediately and call Festool directly at 1-855-784-9727. This thread is closed temporarily for discussion. We will reopen this thread and provide more information once it becomes available. Thank you for your patience." Quote
..Kev Posted July 16, 2013 Report Posted July 16, 2013 Thanks for the info Doug! I'm in the US but, think I'll give a call and follow up. Quote
cgrello Posted July 16, 2013 Report Posted July 16, 2013 Got a call about mine today. Their customer service is great! Quote
..Kev Posted July 17, 2013 Report Posted July 17, 2013 Their customer service is awesome! So, they gave me a free upgrade to the 75! Wonder if the guy that won Marc's saw will be getting the free upgrade? Quote
EdgewaterWW Posted July 17, 2013 Author Report Posted July 17, 2013 The guy (Me) that won Marc saw can't get a upgrade because the TS55 is not recalled just the TS55 REQ. Quote
..Kev Posted July 18, 2013 Report Posted July 18, 2013 That's what I get for not paying attention to who won the saw.. Bummer! Thanks for the info! Quote
EdgewaterWW Posted July 18, 2013 Author Report Posted July 18, 2013 No bummer, I got a free saw. Marc got the bummer! Quote
..Kev Posted July 20, 2013 Report Posted July 20, 2013 So, they next day aired the new saw to me! Got here just a bit ago! Awesome customer service! Quote
cgrello Posted July 21, 2013 Report Posted July 21, 2013 TIODS... How do you like the 75 compared to the 55? I'm still undecided on whether I want to wait for the fix for the 55 or trade for the 75. Quote
..Kev Posted July 21, 2013 Report Posted July 21, 2013 I was concerned when I first unpacked it as it's a bit bigger and a little heavier than the 55. So far, I've only used it twice but, I think it slides better on the rails and seems a little better balanced. Obviously, it can handle thicker material as well. Overall, I'm happy with the upgrade. With that said, I'm not sure that I'd of paid the difference in price for what I do. Quote
Trip Posted July 21, 2013 Report Posted July 21, 2013 ==> How do you like the 75 compared to the 55? owning a 55, 55R and 75 -- There is quite a bit more 'play' in the 75 as compared to either the 55 or 55R so the cut's are a bit rougher and perhaps a little more slop. The 75 slides with more 'authority' across the track and through cuts in 3/4" sheet goods. The 55 seems a tiny bit better built over the 55R -- it's hard to quantify, but I used both saws side-by-side yesterday to break-down four 4x8 sheets of 3/4 BB and two 4x8 sheets of 3/4 melamine coated particle board (used to be called shower board), I found that they do have a different 'feel' and the 55 just seemed more 'solid' through the 3/4 BB. I could not tell the deference on the 3/4 melamine. However, having the two scales on the 'R' was a time saver -- I was making several different sized platens for vacuum pressing, so the partial-depth cuts were far quicker with the 'R'... As a side note: I strongly suspect there is a 75R in the offing (probably early next year), so I suspect that FT is clearing inventory of the 75 at the same time as solving issue for their customers.... I arranged for a swap of my 55R when the problem is identified and fixed... Quote
DustinK Posted July 22, 2013 Report Posted July 22, 2013 I just bought the TS55R a month ago and saw this now too. I haven't decided on which option to go with. Are there any features that the TS55R has that the 75 doesn't have? I like the idea of being able to make deeper cuts, but not at the expense of other features or quality. Quote
Trip Posted July 22, 2013 Report Posted July 22, 2013 ==> TS55R has that the 75 doesn't have? Basically, a TS75 is a bigger TS55. So if you review FT's web video promotion for the TS55R, they highlight the differences... Because there are quite a few differences between the R and non-R saws, and several of the 'improvements' make sense, I suspect that the 75R can't be too far out.... If you need to regularly go beyond 3/4" sheet goods, I'd seriously consider the 75. Many folks break-down stock up to about 1.25" with the TS55, but it's not really the right tool for the job... It works, but if the stock is hard maple, the saw really struggles and can torque-out/overheat/etc -- i.e. not the right tool for the job... That's where the 75 comes in... If you need the extra capacity only occasionally, then the 55R is probably the better saw... Quote
F15Todd Posted August 3, 2013 Report Posted August 3, 2013 Has any one sent their saw in for the repair? Just trying to find out how long the turn around is. Festool was not able to give me a time frame when I called. Quote
DustinK Posted September 17, 2013 Report Posted September 17, 2013 Has any one sent their saw in for the repair? Just trying to find out how long the turn around is. Festool was not able to give me a time frame when I called. I sent mine in for repair about a month ago and haven't heard a peep from them since. I just called their customer service and they said that they're still waiting on a fix for the problem, so they're essentially on hold. This sucks, I was under the impression that there was a fix already in place before I sent my saw in, so now it's a month later, I still have no saw, and there is no clear timeline on when I'll get it back. Quote
Chuck Melton Posted September 18, 2013 Report Posted September 18, 2013 Sounds like I should keep an eye out for TS 55 REQ refurb sale... Quote
Trip Posted September 18, 2013 Report Posted September 18, 2013 Think we just have to call it for what it is --- FT really screwed the pooch on this one -- far worse than the Euro Carvex recall... Those who sent their units in won't be getting them back for a long time... Here is what I've heard -- mostly on FOG and mostly until the threads are closed down... a- The riving knife issue is being widely reported/discussed and may or may not be the actual recall issue -- the question has been put directly to FT, but they won't comment... b- For the 'R', the saw's internal DC was redesigned. It's been reported that if you run the saw without significant vac-draw (like a CT on 'high'), sawdust accumulates in the riving knife mechanism. During a plunge, the knife will extend, but not retract after the cut. In short, the riving mechanism jams. The implication is that the riving knife mechanism fails unless you use a high-quality vac attached to the saw... c- If you've ever looked under the hood at the guts of a 55/75/R/etc, then you'd see the fix may require a redesign of the saw body. The 'R' has been available in Europe for quite a while -- so we're talking about an expensive and time consuming fix... d- The fact that the govt's now involved means that FT has to prove root cause and successful remediation -- all that takes time. e- The rumor is that the fixed units won't be available until '14. PS: I've got an 'R' now and happily using it... but i'm also keeping my eye on the riving knife... I won't be sending mine in for repair until folks have their fixed units in-hand... Quote
ChetlovesMer Posted September 18, 2013 Report Posted September 18, 2013 There's only one way to make this right! Clearly Festool should send me an OF 2200 router for free. That seems fair.... doesn't it? 2 Quote
Trip Posted September 18, 2013 Report Posted September 18, 2013 ==> Clearly Festool should send me an OF 2200 router for free. Go for it... If you're successful, let us know who to call... BTW: if you're out a track saw and need one, you can always call them and go for the TS75 option... Quote
..Kev Posted September 18, 2013 Report Posted September 18, 2013 I went for the 75 and have been very happy! Quick, easy, and painless! Quote
davestanton Posted September 18, 2013 Report Posted September 18, 2013 I think the problem is restricted to the US. No problems in Australia that I have heard of. Quote
Trip Posted September 18, 2013 Report Posted September 18, 2013 ==> is restricted to the US As reported on FT-Talk, the problem is with all the saws... It's only a matter of time before the recall expands -- the problem is inherent in the design of the saw body/plunge mechanism itself --- nothing to do with the US/Canada electrics, labeling, packing, etc... The issue has been reported on the FT EU boards as well. As of right now, it's a voluntary recall. Once US-CPSC/Health Canada do their thing, the recall becomes quite a bit less voluntary... The current voluntary recall only applicable in the US and Canada -- for now. The recall may never reach down under -- you guys seem to be a less litigious and 'govt must take care of all our problems' society... Of course, I've watched Australian-rules football, so it could just be down to brain damage... Note: The issue can be rather serious -- after the plunge, the blade sometimes doesn't retract fully into the housing -- that can really make for a bad day... Quote
F15Todd Posted October 2, 2013 Report Posted October 2, 2013 Happy days! I sent my saw in back in July and when with option 1, fix it. Yesterday another email come about the recall, telling all users to stop using the saw and send them in. Today I got an email saying the repaired saw will start shipping back to owner today. And should have it in 7-10 days. About time. Quote
Trip Posted October 2, 2013 Report Posted October 2, 2013 Got the same e-mail... I checked over on FOG -- they refuse to say what the 'issue' is, what the 'fix' is, what parts have been replaced, etc... The only active thread states that the saws will be repaired and begin shipping over the the next few weeks... What's a bit disconcerting, there is a post from a Festool employee that indicates threads relating to specifics will be removed/etc... They have locked several threads and combined/removed posts related to the actual 'issue'... I've looked for posts that I know existed just last week on the details of the problem, but they are gone... Festool claims that they aren't 'allowed' to inform the public per CPSC rules --- that's just BS... FT just doesn't want the public to know what the problem is or how can be fixed... It's just like the original Carvex and/or Kapex issues -- FT doesn't like to admit when they've screwed the pooch... I've got one saw in the shop that I did not send in for repair (I just find a track saw too useful to be without one). It will be interesting to compare 'fixed' -vs- 'non fixed'... I think I got the 'issue' over the weekend -- the saw kind of 'stuck' after ripping some 6/4 stock... It will be more interesting when I post the fix over in FOG and see how long the thread lasts Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.