Slmize Posted October 4, 2013 Report Posted October 4, 2013 I was hoping that someone could help me figure out what I'm doing wrong here. I am making a child's rocking chair. I have made one before using a straight cut pattern bit, but had to flip it(the wood) over due to the thickness of the wood. I bought 2 up cut spiral bits that would cover the thickness. when I tried to use it in my router table both times it grabbed the wood, kicked back, cutting deep into the blank. Don't know what's going on as I'm very new to wood working. I am trying to attach a picture, but not having much luck. Any suggestions would be appreciated.. thank you, slmize Quote
Guest Posted October 4, 2013 Report Posted October 4, 2013 you are cutting too much material at one time. are you pattern routing (i.e trying to shape the outside if the wood) or are you trying to cut a groove through the wood? if you are pattern routing cut as much as you can with a jigsaw and then just use the router to clean it up. This depends on the size of the router bit, but if you are using a 1/2" cutter (not shank size, but the size of the cutter itseld) you should only trim away 1/8" or so at a time. if you cutting a groove, cut it only 1/4" deep or so at a time. Also you might be climb cutting. you wantto push your wood into the rotation of the cutter, not with the rotation. if you cut with the rotation the cutter will grab the wood and sling the wood across your shop, like a baseball pitching machine. google "router climb cut" to see what i mean. Quote
Slmize Posted October 4, 2013 Author Report Posted October 4, 2013 I am pattern cutting. I dont believe im taking to much because it happens as soon as i touch the wood to the bit. As for feeding the wood, i am feeding the bit from right to left. Also its more of a kick back than pulling away from me. I will keep trying to post a picture so i can show what it doing. I may not be explaing it right. Thank you Quote
Guest Posted October 4, 2013 Report Posted October 4, 2013 to post a picture select "more reply options" right below the text box. Quote
Slmize Posted October 4, 2013 Author Report Posted October 4, 2013 I dont have a pin. Not sure if i can put one on the router table it an inexpensive small table. Quote
Slmize Posted October 4, 2013 Author Report Posted October 4, 2013 it says the picture is to big. trying to make it smaller. Quote
Slmize Posted October 4, 2013 Author Report Posted October 4, 2013 ok I think I have it attached. hope this helps explain what is happening. thanks, Quote
Tpt life Posted October 4, 2013 Report Posted October 4, 2013 Find a way to use a pin. You are not steady enough free hand to start the cut. If nothing better on a small table, clamp a board to one edge of your table. It works better when the pin is closer to the cutter though. Quote
Guest Posted October 4, 2013 Report Posted October 4, 2013 also i wouldn't start at the corner if that is what you are doing. that is where grain changes direction and gets caught on the cutter. start in the middle add follow through the end (rather than going around the corner) and then the turn the board around and do the other side. Quote
Slmize Posted October 4, 2013 Author Report Posted October 4, 2013 Ok thanks i'll try that. Thank you Quote
T-astragal Posted October 4, 2013 Report Posted October 4, 2013 Danger! You gotta be on a bearing, a fence or a pin before the bit hits wood. If you can't do that, start on some nice long grain. Or screw a lead in bock to the pattern and remove it to finish the cut Steve Quote
Beechwood Chip Posted October 4, 2013 Report Posted October 4, 2013 Here's a good video on pattern routing. Skip to about 6:30 for your issue. Quote
dwacker Posted October 4, 2013 Report Posted October 4, 2013 You're cutting the wrong direction. You need a bottom bearing bit or pattern on other side. Look at the grain. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.