Pbmaster11 Posted December 23, 2013 Report Posted December 23, 2013 Why not have a down draft table as your bandsaw table? would help collect that dust that collects on the table? I know bandsaws are notoriously hard to collect dust from. Quote
Trip Posted December 23, 2013 Report Posted December 23, 2013 ==>^^^ Band saws are more problematic than some tools, ex. a planer, but not impossible... I've got no problem capturing 99% from my band saws... Band saws require about 650+CFM at the tool... Most folks start with a 1100-1200CFM at the fan, but by the time they get to the tool, it's dropped below what's effective... Quote
dwacker Posted December 23, 2013 Report Posted December 23, 2013 Air blowing down into the kerf helps much more than on would think. I left my air hose off by accident and the difference was very noticeable. Quote
Trip Posted December 23, 2013 Report Posted December 23, 2013 ==> Air blowing down into the kerf helps much more than on would think. That's a good point... For years, I kluged-it.. Had a single POU on a reel... Moved between wide-belt, bandsaws and bench. What a pain in the a**. Many times, I was just too lazy to move it at all.. At some point, I got fed-up and bought the copper, compact filter/reg combos, etc and just ran hard-points... Like all shop improvements, kicked myself for not doing it from the start... Quote
dwacker Posted December 23, 2013 Report Posted December 23, 2013 ==> Air blowing down into the kerf helps much more than on would think. That's a good point... For years, I kluged-it.. Had a single POU on a reel... Moved between wide-belt, bandsaws and bench. What a pain in the a**. Many times, I was just too lazy to move it at all.. At some point, I got fed-up and bought the copper, compact filter/reg combos, etc and just ran hard-points... Like all shop improvements, kicked myself for not doing it from the start... My saw has an air pump on the nose of the cast iron motor. Quote
Trip Posted December 23, 2013 Report Posted December 23, 2013 ==> air pump on the nose of the cast iron motor Do you ever have issues with dust clogging the pump? Quote
dwacker Posted December 23, 2013 Report Posted December 23, 2013 ==> air pump on the nose of the cast iron motor Do you ever have issues with dust clogging the pump? My motor, pulley, belts, bearing and electronics are housed in a separate sealed base nothing is ever exposed to any dust. Quote
Trip Posted December 23, 2013 Report Posted December 23, 2013 ==> a separate sealed base nothing is ever exposed to any dust. Nice... I'm assuming there must be some sort of venting for heat/cooling/airflow. Did they put a filters on the vents? Quote
dwacker Posted December 23, 2013 Report Posted December 23, 2013 ==> a separate sealed base nothing is ever exposed to any dust. Nice... I'm assuming there must be some sort of venting for heat/cooling/airflow. Did they put a filters on the vents? I dont know really never looked. There may be some vents in the back door but its alway real clean in the motor section. Quote
wilburpan Posted December 23, 2013 Report Posted December 23, 2013 Here’s how I greatly improved dust collection on my bandsaw. I have a 1940's era Walker-Turner 16" bandsaw. I just love using it, with one exception. This bandsaw was built in the day when dust collection was pretty much a nonexistent issue. As such, there were no good dust collection devices for this bandsaw.Some of the solutions that I've seen for this issue for vintage bandsaws have involved using sheet metal to fabricate a hood or cutting a hole in the bandsaw wheel covers to accommodate a dust collection hose. I don't really have a good way of dealing with sheet metal, and I certainly don't want to put a large hole in the cast iron wheel covers of this bandsaw. Here is my solution. A while back I picked up a 4” dust collection port from Woodcraft, and at the time I was holding it thinking, "If there was only some way that I could make a dust collection device with this for my bandsaw. But what would I make it from?"I was thinking this while staring directly at a pile of scrap pine sitting on the floor of my shop. Seriously.A full ten minutes later: *** headslap ***This is what I made. I basically made this by screwing on the right side, putting it under the table of my bandsaw to see what I needed to notch out, then doing the same with the left side, then adding some cross pieces for strength.On the right side I used a Forstner to drill some recesses, and sloppily epoxied in some rare earth magnets, which will hold it in place. And here it is in action. This dust collecting shroud completely encloses the lower guides of my bandsaw, and collects the vast majority of the dust that used to pile up underneath the bandsaw. I can't put a number on it, but compared to not using it at all, it certainly collects the vast majority of the dust generated when making a cut on my bandsaw. Although this setup is really custom fit for my Walker-Turner bandsaw, the design principles should be easy to apply to any other bandsaw, vintage or otherwise. It's basically a box with an open top and back, with the sides contoured to fit the frame and wheel cover of the bandsaw, and rare earth magnets mounted in an area where they can stick to the bandsaw. There is still some dust that collects on the table surface. I’m pretty convinced this is sawdust that gets carried by the blade through the cut into the lower wheel compartment, around and over to the top wheel compartment, and comes out to land on the table.After making this, I'm just a little surprised that more machinery accessories aren't made out of wood instead of fabricated from metal. After all, we are woodworkers, aren't we? Quote
krtwood Posted December 23, 2013 Report Posted December 23, 2013 Mine is similar to Wibur's, but I have a piece of plywood that wedges between the guides and the table and then hooks into the pin that aligns the two sides of the table so it really can't go anywhere when I'm moving the saw around on its mobile base and stretching out the hoses. I also have the 6" line split into 3 hoses, two 4" and one 2-1/2". The 2-1/2" goes to the back of the lower wheel. Also added some weatherstripping around the lower door which not only sealed things up better but took out all the rattle from my vibrating saw. The only time I get anything significant coming all the way around and back onto the table is if I'm making what becomes a rip cut, with the grain running vertically on the table, end grain on the top surface. Well that and when I can't be bothered to switching the gates around to make one cut. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.