Jim L. Posted February 20, 2014 Report Posted February 20, 2014 Does anybody here have any recent experience with the Triton TRA001 router? I picked one up from Amazon last month and I'm concerned about the depth of the 1/2" collet- it is only 1.09" as opposed to the standard 1.25". I had a 1/2" straight bit start to drift upwards in the collet while I was dadoing some drawer sides on my router table, and I'm not sure if this collet just needs to be tightened a heck of a lot more than my old router, or if I received an incorrect (metric) or defective collet. Is a 1.09" bit insertion depth normal for this router? Quote
Eric. Posted February 20, 2014 Report Posted February 20, 2014 I'd be returning at least the collet if it was drifting while adequately tightened. You shouldn't have to crank the heck out of it, but I give it some decent force...a little less than I apply when tightening the arbor nut on a TS. I've only experienced a bit move in a collet once...when I took it out and looked at it I realized the collet just needed a cleaning and it was fine after that. Just curious...was it an up-cut spiral bit you were using? That's what I was using when it happened to me...the physics of the bit makes it want to pull out so I tend to torque those down a bit more. Quote
Jim L. Posted February 20, 2014 Author Report Posted February 20, 2014 Nope, it was a standard Freud straight cutter. Since then I've been cranking the heck out of it and haven't seen any movement, but I think I will give their service department a call. Quote
tim0625 Posted February 21, 2014 Report Posted February 21, 2014 SECURITYYYY!!! Eric's right... you shouldn't have to crank it. If you've eliminated the schmutz variable (technical terms ) in the collet, sounds like you need to make a call. It's like this....my son was a county deputy. He got an officer in distress call over the radio about 2AM...GOTTA GO!! He turned around and his Dodge Charger was up to 140mph (on it's way to 170) and there was a twitch...a quick wiggle in the rear end.....it's like this router....you don't know exactly WHAT the heck is happening but THAT wasn't right! Make a call before a 10 million rpm router bit makes a Star Trek exit. My son? Oh he found out fast what the problem was...about 2 seconds after the wiggle, the right rear tire exploded at 142mph. The Academy training kicked in...off the gas, no brake... just turn the wheel to keep it straight as the back end tries to drift. He said once you're below 100, it wasn't too bad but that was a long 5 seconds to get there! Quote
Jim L. Posted February 22, 2014 Author Report Posted February 22, 2014 I'm attaching a photo of the router in the hope that another Triton owner can chime in and tell me if this is normal or not. The bit in the photo is completely bottomed out in the collet, and the collet is tight. Note the "Min Insertion" line marked on the bit... and the large gap between the line and the collet. Quote
krtwood Posted February 23, 2014 Report Posted February 23, 2014 I have both Triton routers and they use the same collets. That sounds about right on the depth. The collet itself is definitely less than 1.25" deep so it would only be a question of whether there is space inside the router for the shank to go past the collet. But in that case it doesn't make any difference as far as the collet holding the bit. I've never had a problem with bits moving, including a giant MLCS box joint cutting bit that's super long with half a dozen slot cutters on it. Make sure you aren't bottoming out the bit completely when you tighten it, that can cause it to not tighten properly. Quote
Jim L. Posted February 24, 2014 Author Report Posted February 24, 2014 Thanks krtwood, that's good to know. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.