Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Poly dust in the grain and joints

Featured Replies

Hey guys, I was helping a friend rub out his polyurethane finish on his bar. He had allot of brush marks in it. First we wet sanding with 600 grit, then 0000 steel wool. Everything went well except now all the grain and joints are full of white poly dust, basically it looks terrible but it's smooth. lol Of course another coat of poly will make it disappear, But then we would have to rub it out again and most likely have the same end results.

 

What is the best way to clean out all the dust from the cracks. It seems to have stuck and clumped together from the wet sanding. A vacuum did not work. I want to get it all cleaned before I do the final rub with paste wax and 0000 steel wool.

 

Please Help!

 

Thanks

Typically you only rub it out between coats, not after the last coat.  If you get the preliminary coats down smooth enough the last one should take care of itself.  And you can always dampen your cloth with a little bit of mineral spirits ...

  • Author

How long did you let the finish cure before you rubbed it out?

 

He did the finnish, He said he put 3 coats on it and the last one was a few days ago.

  • Author

Typically you only rub it out between coats, not after the last coat.  If you get the preliminary coats down smooth enough the last one should take care of itself.  And you can always dampen your cloth with a little bit of mineral spirits ...

 

Hmmm, I've never been able to get a perfect last coat, there has always been dust or brush marks, and even sprayed there is orange peel that needs to be rub out. But in this case I didn't build the top or put on the poly.

 

Will the mineral spirits eat into or soften the poly, like lacquer thinner dose to lacquer?

He did the finnish, He said he put 3 coats on it and the last one was a few days ago.

Like sap said, maybe we have a mixup in terminology here. To me, "rubbing out" is finishing the finish ( to get rid of dust nibs and other imperfections). Normally a person would wait for a finish to fully cure, which could take a few weeks depending upon the finish. Then you could "rub out" your cured finish using 0000 steel wool and some paste wax. If using a waterborne topcoat, a little dish soap and water with a white 3m pad should do the trick in place of the wax and steel wool.

Or maybe sand it back a bit with some 220, and apply the final coat with a wipe on poly.

  • Author

Thanks for the info and advice guys. The top is super smooth now, I always considered 600 grit and then 0000 steel wool "rubbing out the finish" I didn't do the finale rub with paste wax yet because I knew I might have to put another coat on to fix the problem.

 

The top is made of cherry, with a boarder or purple heart and a black colored wood(teak?) So the bright white dust is Very obvious and looks terrible.

 

I will try to use mineral spirits to clean the poly dust out of the cracks, maybe with a air compressor to blow it out where it's to deep to get with a rag. If that doesn't work, I guess I will thin his poly with paint thinner and try a final wipe on finish, then just rub it out lightly with 0000 steel wool and paste wax. to try to prevent the same results as now.

 

I'll let you know what happens, Thanks again fellas!

Thanks for the info and advice guys. The top is super smooth now, I always considered 600 grit and then 0000 steel wool "rubbing out the finish" I didn't do the finale rub with paste wax yet because I knew I might have to put another coat on to fix the problem.

 

The top is made of cherry, with a boarder or purple heart and a black colored wood(teak?) So the bright white dust is Very obvious and looks terrible.

 

I will try to use mineral spirits to clean the poly dust out of the cracks, maybe with a air compressor to blow it out where it's to deep to get with a rag. If that doesn't work, I guess I will thin his poly with paint thinner and try a final wipe on finish, then just rub it out lightly with 0000 steel wool and paste wax. to try to prevent the same results as now.

 

I'll let you know what happens, Thanks again fellas!

Use mineral spirits instead of paint thinner to make your own wiping varnish. Go 50/50 oil based poly and mineral spirits.

  • Author

Use mineral spirits instead of paint thinner to make your own wiping varnish. Go 50/50 oil based poly and mineral spirits.

 

Will do, Thanks for the tip!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.