Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Non-Flammable Finish

Featured Replies

Forgive me if this has been asked before, I didn't come up with anything during my searches in the Forum.

 

I am making some candle holders (see attachment) which are square with "posts" in the corners and Lexon slid into channels inbetween the "posts". There will be a candle in the center in a shot glass style holder, with sand and / or or rocks around the perimeter inside.

 

I am considering adding mitered pieces to run the perimeter of the top to hide the end grain and top of the Lexon. which are the pieces that concern me as they will be closest to the heat of the flame.

 

What I am looking for is a firesafe finish that preferably comes in a spray can. I have spray polyurethane, I'm wondering if I could use that as long as I let it off gas for a week or so before putting any candles in it?

 

Any suggestions would be greatly appreciated!

post-7495-0-19438500-1403015841_thumb.jp

  • Author

I doubt any hard-curing finish will be a problem. Linseed or tung oil might be a little worse. Shellac MAY be a little more fire resistant, but probably not by much. Scorching or bubbling may be more of an issue

 

By "hard-curing" you are meaning anything that leaves a coat or film on the surface, like Poly?

  • Author

Yes, poly, lacquer, shellac. All available in spray form. Honestly, the Lexan is as susceptible to heat damage as the wood finish, if not more so. It looks like your enclosure is spacious that you shouldn't have any problems, providing the candle stays upright and centered.

 

Ok I have some spray poly, I will use that since it's on hand. I was worried about the Lexon too, but as you said given the spacious area around where the candle will be I think it will be ok. I am contemplating hotgluing the candle holder (think shotglass like shape) into the center of the piece to keep it from moving around, so that should help keep it centered and what not.

 

Thanks for your help!

2 issues: heat and volatility....Candles are not a lot of heat....Personally, I think you let the spray poly dry a couple hours, maybe a day and you're fine.  I don't think the fumes would be that volatile either.  Build it, light it, put it in the driveway for a couple hours.  If no bond fire, bring inside.  Question, glass is pretty cheap, especially when you build it to use something already commonly used and cut like 6x9" panes.  Why not glass?

  • Author

2 issues: heat and volatility....Candles are not a lot of heat....Personally, I think you let the spray poly dry a couple hours, maybe a day and you're fine.  I don't think the fumes would be that volatile either.  Build it, light it, put it in the driveway for a couple hours.  If no bond fire, bring inside.  Question, glass is pretty cheap, especially when you build it to use something already commonly used and cut like 6x9" panes.  Why not glass?

 

Makes sense, good idea on letting it burn outside first! As for the glass, I have never used glass in a project before, and I have never cut glass before. I had the Lexan (apparently I have been spelling that wrong) on hand already and can cut that pretty easily with my miter saw so I just used that. It's just as clear as glass once the film is removed.

If you want to hide the Lexan tops, you could just use some edge banding and trim to shape.  I'd personally just sand the edges to a polished finish, and maybe put a tiny square cap on the posts - only a hair oversized to hide the slots, maybe dowel mounted so you can replace things if you need to.

 

If you want to try glass, look for windows on trash days.  There's usually someone tossing a single window, sometimes more.  Might have to go a while to find it, but they'll be there.  Get it home and practice before you use it for the project.  I've gotten better, but I still need practice.  I've found sandwiching the pane between plywood sheets helps... but don't kneel on it to hold it in place.  (Voice of experience.)

  • Author

If you want to hide the Lexan tops, you could just use some edge banding and trim to shape.  I'd personally just sand the edges to a polished finish, and maybe put a tiny square cap on the posts - only a hair oversized to hide the slots, maybe dowel mounted so you can replace things if you need to.

 

If you want to try glass, look for windows on trash days.  There's usually someone tossing a single window, sometimes more.  Might have to go a while to find it, but they'll be there.  Get it home and practice before you use it for the project.  I've gotten better, but I still need practice.  I've found sandwiching the pane between plywood sheets helps... but don't kneel on it to hold it in place.  (Voice of experience.)

 

Great idea with the Edge Banding! I have never used it before, but I orderd some so we'll see how it turns out. I have some scraps I can test with that are cut the same as the posts on the project. As far as polishing the edges of the Lexan, I wouldn't know how to do that. I haven't examined them closely to be honest but given I used a mitersaw to cut them, they probably aren't pretty. May add character to the piece though :)

 

I have a bunch of glass that I salvaged from a project at work a while back, I haven't used it because it is tinted green or some odd tint. Plus I don't know the first thing about cutting glass, or even if the glass I got is tempered or not.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.