Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Oil stain not dark enough. Help.

Featured Replies

Hello all. New here. I'm refinishing a piece of furniture that was built with different types of wood. I used red mahogany oil penetrating stain. The sides and the top of the piece are birds eye maple and the rest of the piece is mahogany .

After two coats of red mahogany I figured out it was never going to be dark enough. So I tried to use a walnut gel stain. The gel stain does not penetrate when used over the oil based penetrating stain. It simply didn't make any difference in the color.

What is the best way to darken the birds eye maple so that it looks more like the color of the mahogany?

Thank you!

52f175b72bd88b5fed498e9183918ce8.jpg

you will have a hard time finding people here who will endorse staining birdseye maple.   Nature made it beautiful and dense for a reason :).  she does not like to be messed with.  

 

if you can spray a toner you will get better results.  A toner is basically a tinted top coat.   Mohawk makes them in aerosal cans.

 

http://www.mohawk-finishing.com/catalog_browse.asp?ictNbr=171

  • Author

Thanks for the input Mike. I would not normally stain birds eye maple but the piece looks so awkward with two different colors of wood.... and since it's made of mahogany and birds eye .... Before I cleaned the wood you couldn't even see the birds eye but it's beautiful.... 84ef827e44d6c41da2b3c57d31e7953f.jpg

The problem with the oil based stains is that they are also sealers. Basically varnishes with pigment added. So one they're dry, you won't get the wood to accept any more color because the resins in the Minwax have sealed the wood.

In the future, your best bet would be to use a water or alcohol based dye first, in different concentrations/colors for each wood species, to get the colors of the different woods close. Then seal with a wash coat of shellac or really thin varnish. Then use the gel stain as a glaze to make minor color corrections where needed. Finally, topcoat with your clear.

Since you've already sealed everything up on this piece, you have two choices. Either sand back to bare wood, or build more color on top by using glazes and toners (tinted varnish or lacquer). Adding color on top will muddy the grain again. Sanding back to bare wood, well, that'll be a heap-o-work, but will allow you to use the process above, starting with the dye. Neither is likely a very appealing solution though

Polyshades is going to obscure the grain by the time the color is dark enough. Dye on raw wood or spraying toner is going to give the best results.

  • Author

Thanks wdwerker. The grain on this piece of furniture was obscured before I started cleaning the finish. And when I begin cleaning with mineral spirits, the finish dissolved and I could see birds eye maple. So I'm just trying to get back to a point where the piece looks a little more cohesive. It is made of mahogany and birdseye maple and looks really strange with the two contrasting colors and grain patterns. Ugh

I agree. Poly shades is heavily pigmented. Almost like paint. Dilute heavily because if it's too dark, you're stuck. It's polyurethane, so there's no easy way to get it off once it's on, other than sanding it off.

  • Author

Well, my really light coat produced very little change in color. I'm at a disadvantage because I have nothing to test with. I'm concerned the small - 1 x 6" test strip on the side is not large enough to see the difference. Going to try poly in red mahogany.

  • Author

Wondering what the heck was on the wood before...tinted shellac? Whatever it was, it produced an even appearance in the color of the piece.

Well, my really light coat produced very little change in color. I'm at a disadvantage because I have nothing to test with. I'm concerned the small - 1 x 6" test strip on the side is not large enough to see the difference. Going to try poly in red mahogany.

 

Can you remove the top?  Usually tops are just screwed on.  If so, use the underside of your top as a test panel.  

  • Author

Bob, I thought it was tinted lacquer but I have never used it. Yes Mike I can remove the top I had not thought of that. I will give it a shot. Thanks

  • 4 weeks later...

Dye. Get some dye. It will even out the color and not obscure the grain. Lockwood wster based dyes are excellent.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.