Jake Broadbent Posted December 8, 2015 Report Posted December 8, 2015 First Journal here for me and although my project is well underway I wanted to write up a journal for it and share what I learned and maybe get some more advice on how to do it better for future projects.Long story short. I wanted to build a statement piece in the house and I wanted it to be a wall hanging media center/cabinet. I watched the askwoodman floating media center build and took a few things from it but I also really liked marcs walnut ply media center. So I have married them(in my head). This is the biggest project I've taken on but the Wife says I cant get anymore tools or clamps until I start working on the honey-do list.the top is going to be solid walnut with the dividers being solid walnut as well with the bottom and 2 sides pieces being import walnut plywood. This was also the first project where I started with completely rough lumber.This was the glue up for the top.There are about 6 Dowels in it to help keep it straight, Probably excessives on the clamps? But hey. it was flat and well glued. This was just over 8' long and just a bit over 15"wide with a thickness of 17/18" I also had to fill in a few holes with epoxy where there were some knots in the top. I used the West Systems epoxy with dark brown trans tint . I think it will help make everything look really nice when it is finished.After that I rough cut the plywood to size and used a flush trim bit to make them both exact copies of eachother. I don't have any pictures of that process but it was the first time using that bit and it went extremely smooth.I like how Allan Little did his dividers with the sliding dovetails and keeping them nice and open for all the wires and to leave plenty of space for air flow. Again no pictures but it was the first time doing Mortises and Tenons. I did not have an up-cut spiral bit at the time so I had to use a crappy straight bit from a set I was given. It wasn't very fun and it took a lot of passes but I did manage to get them to come out pretty nice. I have however ordered a nice new Whiteside bit to help with them in the future. After that I made a ghetto router table fence with some mdf to make the male part of the sliding dovetail. Again I've never done this part before but again, extremely smooth I had no issues whatsoever. I do however eventually want to make a more dedicated router table.This picture was taken after all the work was done. as seen by all the wood dust/pieces on the ground. Nevermind the dog bone on the left. I don't let them out there when making too much noise.I then marked where I wanted all of my dividers to go on both the top and bottom boards very carefully.. had a cup of coffee or two and re-measured and checked everything a couple more times. Then made a little template for my router so I could setup a straight edge and make the dovetail cut easily. Then made the 3 cuts.I have no photos of them at this point I do however have some pictures of when I did the dry fit.After this I cut the dadoes into the top of the top (oops!) , Well I fixed it somewhat by glueing in a new piece of walnut going the opposite direction, Let's just say I did it for the design? or for the added strength? .. Anyways. I fixed the mistake then cut the dadoes in the correct side of the boards.Here it is with the end boards.After the dry fit (and everything was nice and square I cut a recess into the back of each divider to run a 8' long x 3" piece of walnut on both the top and bottom of the divider that will be what I use to hang it on the wall. I think I might even use some pocket screws on the back to get them to attach the 2 end pieces of the media center. Still debating if this wall actually add anything or if it is just a waste of time. No pictures of that currentlyI decided before I did any of the glue up I would finish some of the boards on the inside. First I taped off all of the glue areas then I used a General Finishes Walnut water based dye then after that dried I used a natural finish Danish oil and wet sanded that in to do some grain filling. I'm not so worried about filling the grain on the inside but I figured it was good practice for when I do the top which is where it will really matter. I think I really made the right decision of prefinishing (all except the semi-gloss poly) because the glue up was a bit less than fun.I'll continue this with some more pics tomorrow night. Thanks for reading, 1 Quote
bushwacked Posted December 8, 2015 Report Posted December 8, 2015 ooooh this looks great so far! I will enjoy watching this come together because I have about the same idea for some of my stuff ... Quote
shaneymack Posted December 8, 2015 Report Posted December 8, 2015 Looking good Jake! More pictures would help! Im trying to understand, you mortise and tenoned the joints of the divider and sliding dovetailed them into the case? Its hard to see in the photos. Sent from my SGH-I337M using Tapatalk Quote
Jake Broadbent Posted December 8, 2015 Author Report Posted December 8, 2015 Well the dividers are made up of 4 pieces. Mortis and tenon'd together. Then I ran the top and bottom of that divider along the dovetail bit.I wish I had taken more pictures but I also was focused on getting some work done. A lot of props to everyone who does a journal.A lot of the work I've done has been figuring it out as I go, and my terminology is not that great yet. 1 Quote
bushwacked Posted December 8, 2015 Report Posted December 8, 2015 curious ... why do the top and dividers solid, but the sides and bottom from ply? I could see top bottom and sides real and dividers ply or something like that, but it just seems like a random combo of mixing ... Quote
RichardA Posted December 8, 2015 Report Posted December 8, 2015 Jake, I'm not being a smart ass, but what is 17/18, as a measurement? Quote
Jake Broadbent Posted December 8, 2015 Author Report Posted December 8, 2015 It's just very shy of an inch. Could be 31/32. But 17/18 sounds more interesting.As for why the ply on the ends? I just liked the pattern on them. Maybe it would have been better to do it out of solid walnut but as far as my thinking they aren't adding a lot of strength plus the wall is recessed a bit and you will rarely if ever see them. The top is what will be seen most and then eventually I will be adding doors(2 in the center) you won't see the inside very much. Quote
Jake Broadbent Posted December 9, 2015 Author Report Posted December 9, 2015 So although I'm working 12 hours a day right now I did manage to get enough time tonight to attach the top rail piece that I will later cut at an angle with the circular saw. I don't have a long enough straight-edge but I do have plenty of MDF and some cut offs from plywood that might be long enough, any suggestions for me when I do this?Eventually I need to upgrade the lighting in the garage as I don't really have very much.I also found/took some pictures of where this will be going.I cut out where the cabinet will hang from and put in a piece of walnut plywood and ran the wires through it. 2 HDMI, 5 Speakers and 2 outdoor speakers, the subwoofer, an optical cord and an outlet. I also added an outlet behind the TV. Theres more holes in the wall where I ran more speaker wire for some wall mounted speakers for the left and right speakers. Not worried about the holes because i'm pretty decent with drywall and the wall will be getting finished with stacked stone down the middle to tie it into the kitchen island that I redid before moving in.unfortunately I tried to hang the board on the wall by myself and added a few unnecessary holes but I think once I fill them in it wont be noticeable. I have some of the timbermate wood filler, would this work ok or anyothers suggestions?so you can get an idea of what the rock will look like.Tomorrow I will try to get started on the bottom rail/trim piece.Any suggestions are appreciated. Quote
bushwacked Posted December 9, 2015 Report Posted December 9, 2015 Wow the kitchen looks nice! Can't wait to see that wall done as well ? As far as trim ... Take your time and make sure your miters are snug. Quote
boelkers Posted December 10, 2015 Report Posted December 10, 2015 This is going to look great when its all finished! Quote
shaneymack Posted December 10, 2015 Report Posted December 10, 2015 Jake you could plug the holes. Drill them out with a 3/8" forstner bit and cut some tapered plugs out of the same material, Quote
Jake Broadbent Posted December 10, 2015 Author Report Posted December 10, 2015 (edited) I think I might just do that. Going to see what holes will actually be seen. Tonight when I get home from work I'll be cutting the angle on the trim pieces. Edited December 11, 2015 by Jake Broadbent spelling Quote
Jake Broadbent Posted December 11, 2015 Author Report Posted December 11, 2015 Well I got all the top and bottom trim cut. I wound up going at only a 10 degree angle. The wife likes the look too so I spent the last hour or so sanding out all the saw/burn marks. I used a straight 8' piece of plywood that was about 4" wide and reinforced it from behind with some oak cauls I have that way when I was pushing the saw along the "fence" it wouldn't bend at allTomorrow I will sand the trim more and maybe get to the stain. I wont be able to take any good pictures until Wednesday when I am off next because I haven't seen the sun for a few days now.I'm thinking about the doors. The wife wants the 2 center sections to be doors and has already found the brushed nickel hardware for them. Because they will be seen all of the time I wouldn't mind getting some walnut burl veneer but I don't know if that would be too much or just not worth it for this(not to mention ive never worked with it) Anyone have any good ideas for me? plywood, solid wood, veneer, etc. Thanks! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.