Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Next set of guitars...The RevCasters

Featured Replies

  • Popular Post

Getting ready to do the next set of guitars. While I was out on tour The Rev from the band Success played one of my basses and ordered a set of teles with some mods ...

So here are the common wants no pick guards , one single coil , set necks, one volume no tone from there he let me have some freedom.

Rev caster one

Poplar body with maple top

Purpleheart /maple neck with maple fretboard

Revcaster  two

One piece Jatoba body

maple / jatoba neck with a jatoba fretboard

 

But first we need to do a little design work First step we need that Classic tele shape but my own . We started with a hard board, cut out on the band saw and smoothed the curves by hand and with the spindle sander.  After the happiness was achieved to 1/2" MDF board we go. Along with a dedicated centerline and hidden pattern mountng spots. I use alot of two way tape in my guitars but if I screw to a body I can change templates and reattch them as needed so if you can find a spot to hide a screw hole go for it.

IMG_8905_zps7c7jmxyf.jpg

Now I needed a headstock shape. So armed with a ruler and some tape rolls and jar lids to make curves this is what we got.

IMG_8906_zpskoxrwznl.jpg

Tape the headstock right to the MDF and draw out the neck with the center line. This cut out on the band saw. I cut out the main neck length with a 1" blade which makes it very easy to hold a nice straight cut with out those band saw marks.

Side note though i have all these nice work surfaces and here i work on the damn garbage can.

IMG_8907_zpsr8zffjvc.jpg

IMG_8908_zpsjkiivov8.jpg

Here it all is all together

IMG_8909_zpsf7sfapen.jpg

All center lines should line up (seriously they mean everything)

IMG_8910_zpszimjg60m.jpg

  • Author

Next we have some wood selection... I have had this one piece Jatoba I have been dying to use. Its just big enough for 2 bodies

IMG_8922_zpsiqvfzogg.jpg

IMG_8923_zpswtfdcqpj.jpg

I cut out the bodies on a combo of the 14" band saw with a 3/16" blade to rough it out and then on to the shaper with Heilx byrd cutting head

IMG_8926_zpslflsszyt.jpg

Poplar and maple top

IMG_8935_zpswpcz8ccx.jpg

IMG_8936_zps3rpvtn3q.jpg

 

I tend to make neck blanks in bulk just cause it is much easier and I like to have a selection when needed

IMG_8913_zpsf7hhdroa.jpg

I settled on one with purpleheart and one jatoba and these both got the same treatment of the small band saw and shaper

IMG_8917_zpsqknc26y2.jpg

37 minutes ago, bgreenb said:

Subscribed. I love following guitar builds. 

Me too ... because chair builds don't make me feel bad enough about myself. :)

  • Author

I was asked about what i use to do 80% of my pattern cutting with.

I picked up this beauty used for $250 for the 3HP model

F5F3E6A6-8773-42F5-B96F-FE14537A160D_zps

I bought the cutter and bearing new from Shellix for around $200 but this thing cuts like butter all most tearout even on the Jatoba

8F5C9F47-0148-4D63-B0A8-3C7C20139C81_zps

i Had to remove some of the steel dust control shroud to fit some of the tight curves I needed to do

F8A4264C-584D-4C8B-A62B-02C48CAB443E_zps

  • Author

Moving on to finger boards. I took piece 5/4 flame maple stock and butterflied it to find a great finger board. I used a 17" band saw with 1" resaw blade to split these.

IMG_8947_zpskxuyezkc.jpg

Then on to the most hellacious part of guitar building... radiusing the fretboard. It is a grulling tast that you feel in your shoulders . I tend to do it for a few minutes move on to something else. then come back do some more.

IMG_8965_zpsgzqjhb0j.jpg

I slotted the fret boards next on a dedicated old dewalt radial armsaw and then back to the shaper again and trim out the fret boards. Now lets see em roughed together

IMG_8980_zps4vrkcvxr.jpg

IMG_8979_zpswxpttwqt.jpg

After the test fits I marked out the centers for the side and top dots. For the side dot I use aluminum which shines up nice for dark stages. Why 3 dots at the 12th fret...why not

IMG_9001_zps79nueg5t.jpg

The top dot will be maple and purpleheart

IMG_9017_zpsvj0mbvzr.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.