Recommended Posts

Posted

This is set up in the ground level utility room I'm using in the museum house I'm working on now.  If I don't have a sink to use, I normally use oil stones.  This setup is my first choice, and fastest honing setup.

Stones are kept in the right sink of the fairly standard double stainless kitchen sink.  Stones are Sigma Power 400, hard 1,000, 6,000, 10,000, and 13,000.  The weird thing up on the edge of the sink is a Seuihiro Cerax (spelling not promised to be correct) 3,000 to fill the 1k to 6k gap.   The smaller the gap, the fewer total strokes needed.  Typically it takes about 10 strokes on each stone in this progression.  I don't do micro-bevels, or ruler tricks.

To the right of that sink are a couple of original Eclipse guides, a Mark II, and an old Record with a small ball for the roller.  A LV plane screwdriver makes ideal work of tightening screws on guides.

In the left sink is a 9 x 12 granite surface plate, that's a jambed tight fit in the sink.  On the left end is an Atoma diamond 140 sheet, and on the right end is an Atoma diamond 400 sheet.  The 400 flattens 6k and up stones.  The 140 catches the coarser ones.  There is room in between the diamond areas for the rubber base stone holder.  The stones are just set in the holder, tightening is not necessary.

On the edge of the left sink is another 9x12 granite surface plate with Diamond Lapping Film on it.  On the end overhanging the edge of the sink are the .5 and the .1 Angstrom films. Under the end away from the sink is a block of wood that holds the plate up so water I splash on it can just run back in the sink. To finish on the film only takes 2 or 3 strokes each front and back, to a mirror shine.  I know you don't NEED a mirror shine, but when it's so fast and easy to do, I'll do it, even with the chisel I carry in my tool belt.

On the counter to the left of the Diamond Lapping Film plate is a pile of paper towels, a  spray bottle of oil, and a trigger start propane torch.  The piece being sharpened gets dried mostly on the paper towels, brushed with the propane flame to make sure, and spritzed with the oil. The paper towels will be dry by the next time I need them, and I'll throw them out at the first sign of souring, but it takes months since they are just bunched up loosely with plenty of air circulation.

To start, a comfortable temperature water is run on the stones.  The first one gets put on the holder, and the work begins.  Any flattening needed is done under running water.  The stones are left on edge in the sink to dry between sessions.

This is the best setup I've ever had, and the one in the shop will be modified to things I've learned doing it like this.

Brendon might be able to tell you the result of a sharpening by this very system.  I honed the iron in the Primus jointer he bought from me not long ago.

Sharp solves all sorts of problems in woodworking.  Sharp is good, but sharper is better.

stonessmall.jpg

leftsinksmall.jpg

besidesinksetupsmall.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   3 Members, 0 Anonymous, 58 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined