Recommended Posts

Posted

So I built a router table for the wing on my TS.  It used to have a router table in it, but it didn't fit my new router, and so I gave my Dad the table and router back.  It had a fence in it, but I didn't get to use it (the fence) much as the only bit I had for the old router was a 1/4" round over.  That got plenty of use, but being a one trick pony with a busted grip, I needed a new router.  

So my next step is designing and building a fence for the router table.  I will be using the fence on the table saw to mount the router fence, as it is square and already there, so why reinvent the wheel. 

So a few questions:

1) How deep should the fence be able to go back from the bit?  I can see the need for running a dado 1" or so from the end of a piece, but if I'm running a dado 10" from the end, then the piece is probably too big to safely use on the table.  So I'm thinking if the fence is able to do a 6" cut, I should be happy.  Anything deeper, I can just use the router handheld and an edge guide, or the TS and a dado stack. 

2) How close should the face of the fence be able to close up around the bit?  

3) How useful is a miter gauge on the router table?

 

Thanks guys.

Posted

You get as many different opinions about this as responses.  The things that are important vary with what you do on a router table.  for me it goes like this:

1) Mine goes about 6" which is adequate for a lot of work at the router table.  Like you, my router table is attached to the tablesaw so for anything over 6"  I just bring the tablesaw fence into play.  For odd configurations I clamp a piece of milled aluminum extrusion into position as a temporary fence.

2) The fence should come forward past the bit about 2".  This gives you adequate travel to step back into even the largest cutters.

3) I wouldn't be without it.  Others could give a hoot.  I place my miter slot on the router table the same distance as the tablesaw blade is from the miter slot on the tablesaw.  This allows jigs to work on both machines with minimal adjustment.

5838bf53dbede_KeyRack(4).jpg.d1108c2396214b2cd557eb6e14759cfb.jpg

5838bf5b0f33a_KeyRack(16).jpg.13981463f4ed7ca44359304e3d0fe8b9.jpg

The one thing I wish for is a little more table in front of the bit.  I only have about 12" and another 4" - 6" would sure change the tipping point of slightly larger panels.  Don't forget to leave a couple of inches of overhang on the front and both sides fro clamping.  there are frequently times when I clamp a stop, additional support, guide or whatnot to the router table.  I use the tool for so much more than edge profiling and dados.

  • Like 2
Posted

I have some 1" thick Nylon boards I'm going to use as the front of the fence (I may rip them thinner, maybe not).  I plan on putting a t track slot on the face and the top of these for stops and jigs.  These will be adjustable to change the size of the opening. 

 

When I built the table, I didn't think to leave enough room in the front for a proper miter gauge, and it sits flush with TS rails, so adding a slot would be pointless as the gauge would only be able to slide a few inches before hitting a rail.    I was going to use just the TS fence for cuts that weren't over the bit, but I forgot to account for the wings of the fence along the rail, they sit about 1/4" proud of the rail on either side of the fence.   So if you look at my scrap box journal, where I show the miter gauge at an angle, you'll see a partially cut T track in the fence I made.  That was me realizing the hard way that I could not cleanly pass a piece across the TS fence on the router table.    So any miter gauge I make will have to slide along the face of the table.

 

2017_05_13_00651a.jpg.0fa11691bd9a701cdc2bca5091067044.jpg 

Whoops!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Who's Online   4 Members, 0 Anonymous, 50 Guests (See full list)

  • Forum Statistics

    32.1k
    Total Topics
    437.6k
    Total Posts
  • Member Statistics

    26,008
    Total Members
    3,644
    Most Online
    Bob44
    Newest Member
    Bob44
    Joined