Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Badge display with inlay - Sapele, Maple

Featured Replies

  • Popular Post

I had originally planned to just post a photo of this as a finished unit but decided to post a few photos of building this instead.  This is a display board for the Asst. Sheriff for all the badges he's had in his career and this will be set on his desk.  The board is about 26" long by 9" high and will slant back at an angle yet to be determined but likely 15° to 20°.  It is made of Sapele and the inlay is Maple.  I'll finish this in Nitrocellulose lacquer.

I gave him a choice of Walnut, Sapele, and a handful of exotics and also gave him some options on inlay, binding, or nothing at all but was hoping all along he would choose this type of inlay because I wanted to do it this way (shocking, I know, but I don't always get to build what I want - I have to build what the client wants - LOL!). 

This sort of inlay work is something I've always done by hand, or in this size with a Dremel and router base, occasionally with a palm router.  But since I built the CNC I thought it only proper to use it to cut the entire piece, including the inlay channel. 

For the inlay channel I used a 1/16" bit at 18k rpm cutting at a slow 25 ipm (didn't want to break the bit). The channel is 0.0625" deep and about 0.090" wide.  I used an X-Acto knife and a carving chisel to sharpen the corners after routing.

To make the inlay I cut two strips of Maple on the table saw and then used the drum sander to get the pieces to the fit I wanted in the channel.  Then I cut the inlay strips to height on the little bandsaw.  The miters were cut with a chisel and the curved pieces were bent on my hot pipe I use for bending guitar binding and cutaways. Start to finish on the inlay was about 40 minutes. 

Ordinarily I use Titebond on something like this but the inlay fit so well into the channel that I just left it in place and flooded it with CA glue.  I took a bread to mow the yard and then came back in to run it through the drum sander again to level the Maple.  After a couple of passes with 120 grit it is ready to fit the badges.  I'll use a Forstner bit and cut recess where the clasps are on the badges so they can be set flush to the surface.

His name will be engraved above the badges but I removed it for this.  When he retires he'll pass this on to his son who is a Deputy. 

Anyway, this is enough rambling on something this simple and small so here are the photos -

Sketch -
001%20-%20Initial%20layout_zpsicc8j7rj.j

Profile cut and inlay channel ready -
002%20-%20Outer%20profile%20and%20bandin

Testing inlay -
003%20-%20Testing%20inlay%20fit_zpsnzlt4

Bending pipe setup -
004%20-%20Bending%20pipe%20setup_zpsu5qj

Dry fit of miter -
005%20-%20Miter%20close%20up%20shot_zpsi

Sanded and with Naphtha -
006%20-%20Sanded%20Naphtha%20applied_zps

Ready to fit for badges -
007%20-%20Ready%20to%20fit%20badges_zps8

More when it's completed - Enjoy!
David

  • Author

LOL!  It is looking a bit ragged, now that I look at it closely.  Cut ok, though. ;)

Thanks, Eric!

  • Author

Got a little closer to finishing today; picked up the badges so I can fit them in place and cut recesses for them to sit flush.  Also, cut the base but still have to cut the angle to allow the front to slant back 15°.  I'll get that done tomorrow and might get to start shooting the finish on but I need to make a Walnut run and that's going to take a while to get over to the sawmill and back.

Base cut -
009%20-%20Curves%20toward%20rear_zpsjvct

Testing badge locations for spacing -
010%20-%20Badges%20testing%20for%20locat

Cutting recess for fasteners -
011%20-%20Cutting%20recess%20for%20badge

More later!
David

Side question, how do you acquire the badges?  Are they from his collection, or did you have more made?  I know from experience it's very difficult to get official badges made without proper paperwork.

  • Author
12 hours ago, Marmotjr said:

Side question, how do you acquire the badges?  Are they from his collection, or did you have more made?  I know from experience it's very difficult to get official badges made without proper paperwork.

They were his actual badges and he left them with us to make this for him.

  • Author

Finished and assembled; one coat of sanding sealer, one coat of gloss, and one coat of semi-gloss Nitrocellulose lacquer.  I let it dry 3 days before assembling it to minimize the chance of the pieces sticking together.  The laser shop will do their engraving today and I'll spray one final coat of semi-gloss on the front before the badges are mounted.  I'm not sure I'll have an opportunity to photograph it fully completed so this may be all I'll post on this little project.

Bottom -
018%20-%20Finished%20bottom_zpspepsawah.

Miter detail -
017%20-%20Finished%20miter_zpsfqucis7d.j

Asst. Chief's view - when I cut the brace piece it seemed like a nice place for a pencil groove so I added that.  My plan was to do it on the router table but the only suitable bit I have was too long so I cut it on the CNC.  I think it adds a nice touch and will be usable for him.  I also beveled the back edge so when he sets his planner book on it there won't be a sharp edge.
016%20-%20Finished%20back_zps3q1olayv.jp

Front side -
015%20-%20Finished%20front_zpsogbti0r5.j

Since it isn't truly 'complete' I didn't spend a lot of time on photography but these will do.

Thanks for following along!
David

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.