Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Epifanes Spar Varnish Over Thompson WaterSeal

Featured Replies

Sorry to be long winded with such basic questions…comes with the job I have … explain explain explain to get proper answers...

Ok I have a few question regarding Thompson Water seal and then a top coat of Epifanes Spar Varnish.

I bought my girlfriend a porch swing for her B-day and it was coated from the place I purchased it with Thompson water seal, very poor job in my opinion, so I disassembled sanded (terrible sanding job from manufacturer) and re-coated it as some pieces were half coated or very lightly coated and the ends were not done etc. I used Thompsons WaterSeal Penetrating Timber Oil Clear, put 2 coats on (two days apart) as it soaked into the wood quite a bit (Cypress) and wiped all excess btwn coats. It will sit for a week before I do any more to it….I may leave it this way for now because of questions I have below…..


I have read you cannot put any type of finish such as Varnish, Shellac or Polyurethane over top of stain or water seal for outside use as it will crack and peel….. Now is this just for outdoor use as the sun, heat, cold, rain, snow etc will ruin it or is it due to being put over another product and not bonding ( I have read so many varying opinions). I use polyurethane over my stained interior base boards and trim with no issue in 17+ years and Epifanes is used on boats in harsh conditions.  What I gather is that it is pretty much a no no to do what I am asking....


The main reason I ask is I also bought a baby porch swing for my 1 yr old son to sit with his mom and use.... and with me his ancient 48 yr old dad (I should have bought a rocker for me uggh 48 and my first kid)….ok back to my questions… The Baby swing was not coated luckily (it was supposed to be), and I am worried about slivers for the little guy (I got 4 redoing the main swing)…So I want to coat it with about 4 – 5 coats of the Epifanes Clear Extra UV Varnish on the arm rests and the piece that comes down to hold him in to protect him from slivers…probably just do the whole swing. I am debating to just do the Epifanes only or with the water seal….ONLY reason for the water seal is to match the colour of the two pieces but that really is not a big deal (I think the varnish will darken it about the same).

Or is there a cheaper Spar Varnish that is just as good I watched the videos here on the Wipe on challenge varnishes would those be better???… I can get the Epifanes for $47 Cnd/L in the Windsor area.

Thanks
Michael M

Thompson's, if you were talking about the original red label kind, is nothing but thinner with wax dissolved in it.  I'd be afraid to hope that any kind of finish would last very long on top of wax.  I don't know what's in their timber oil.  I've not used any of that. I'd wait until it needs to be refinished when the Timber Oil no longer looks good, and then figure out what to do with it.

I've used Epifanes for a long time, and have not found anything any cheaper that lasts as long.  Z spar Captains Varnish is pretty good stuff, but it won't last half as long as Epifanes outside.

Fine Woodworking did a 2 year test of some outdoor finishes.  Their conclusion:

The boards finished with Epifanes, a Dutch marine varnish, and those that were first treated with an epoxy sealer and then finished with Epifanes as shown by Sean Clarke in issue #178 “A Durable Exterior Finish” came through almost unscathed, a hardware store spar varnish had mixed results, while those boards finished with a water-based polyurethane and those finished with a penetrating oil finish did not survive their year-long test.

The best formula was 

1.  Clear Penetrating Epoxy Sealer, followed by

2.  Spar varnish (and they liked Epifanes) put on BEFORE THE EPOXY CURES.

 

I would defeinetly not use the Thompson junk or anything else under the Epifanes.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

Who's Online (See full list)

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,012 Total Members
  • 3,644 Most Online
  • JAR Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.