mikepugh Posted May 31, 2011 Report Posted May 31, 2011 I'm pretty new to wood working, I've made a few cutting boards after being inspired by the videos over @ The Wood Whisperer site and I put together a bassinet out of dark walnut for my new niece. I'm really enjoying the hobby so I've picked up a used Craftsman 6 1/8 inch jointer that I'm guessing is a few decades old but I really like the cast iron tables and fence. I've been trying to get it back to like-new condition by removing all the rust and protecting the cast iron, and I'm now at the point where I want to replace the blades. I've removed the wedge lockscrews but then I go to pry the wedge out using a screwdriver (per the Sears user manual found online) and the thing just won't budge. Not even a little movement - it starts bending my screwdriver and I'm scared the screwdriver is going to break if I push it any more. So the question is - what should I try to do to get those wedges loose w/o doing anything dangerous? Thanks so much! Mike Quote
bywc Posted May 31, 2011 Report Posted May 31, 2011 if it were mine, and they were stuck I would soak it in WD-40 for about 24-48 hours applying more as needed then try again. Quote
Beechwood Chip Posted May 31, 2011 Report Posted May 31, 2011 My standard technique for frozen parts: apply a penetrating oil like 3-in-1, blaster, or WD-40tap with wrench or hammer (vibrations help oil penetrate)waittry to move the partrepeat from step (1) Quote
mikepugh Posted June 1, 2011 Author Report Posted June 1, 2011 Thanks guys - I'll give that a shot! Quote
tim0625 Posted June 1, 2011 Report Posted June 1, 2011 I'm pretty new to wood working, I've made a few cutting boards after being inspired by the videos over @ The Wood Whisperer site and I put together a bassinet out of dark walnut for my new niece. I'm really enjoying the hobby so I've picked up a used Craftsman 6 1/8 inch jointer that I'm guessing is a few decades old but I really like the cast iron tables and fence. I've been trying to get it back to like-new condition by removing all the rust and protecting the cast iron, and I'm now at the point where I want to replace the blades. I've removed the wedge lockscrews but then I go to pry the wedge out using a screwdriver (per the Sears user manual found online) and the thing just won't budge. Not even a little movement - it starts bending my screwdriver and I'm scared the screwdriver is going to break if I push it any more. So the question is - what should I try to do to get those wedges loose w/o doing anything dangerous? Thanks so much! Mike Mike, I have the same jointer - it was in a shop fire and sat in that condition for 10 years before I began restoring it. Rule of thumb...GET BIGGER SCREWDRIVER AND HAMMER!! Seriously, soak it in PB Master Blaster in the morning before work and when you come home for a couple days. It's available at parts stores. Use a larger flat screwdriver and from it's end, pry it from it's bottom upward and it will break free. If not, use a hammer and chisel and bump it on it's end upward. If THAT doesn't work, insert the chisel on the end of the wedge at it's bottom where it sits in the cutter head and tap it with a hammer separating the wedge from the cutter head. For all of the cap screws in the cutter head...soak them with the Master Blaster and if they offer resistance to coming out - move slowly...soak again, because if they round out in the allen head portion of the screw, THAT's bad news...drill, easy out, cuss, repent, etc. Use new cap screws in reassembly and DO NOT buy them from SEARS...someone was smoking something when they Priced them. or should it be or Other FYIs...the cutter head bearings are the same as Sears and cheaper at NAPA. Take your old one in and they match it up. Crazy enough...it's a common bearing that has been used in tool and vehicle applications for decades. Buy knives from SearsPartsDirect.com. I screwed up my cutter head BY ROUNDING OUT ONE OF THOSE (^*%&^& SCREWS and found another on EBay for $5. Not the easiest jointer to set and get right but for the money, it works. Ok...a little crazy on the smileys..it's been a long day in the %^$^%$^%# insurance business. Apply Johnsons Paste Wax and add wood for satisfying dust aroma. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.